User manual SUB-ZERO 600 INSTALL GUIDE

[. . . ] B U I LT - I N R E F R I G E R AT I O N INSTALLATION INSTRUCTIONS CONTENTS Installation Recommendations Installation Specifications Installation Instructions Framed Panel Installation Overlay Panel Installation Completing the Installation Service Information 3 4 8 12 16 20 23 Specifications are subject to change without notice. Check our website, subzero. com, for the most up-to-date specifications. As you follow these instructions, you will notice WARNING and CAUTION symbols. This blocked information is important for the safe and efficient installation of Sub-Zero equipment. There are two types of potential hazards that may occur during installation. signals a situation where minor injury or product damage may occur if you do not follow instructions. states a hazard that may cause serious injury or death if precautions are not followed. Another footnote we would like to identify is IMPORTANT NOTE: This highlights information that is especially relevant to a problemfree installation. SUB-ZERO ® is a registered trademark of Sub-Zero Freezer Company, Inc. B U I LT- I N I N S TA L L A T I O N R E C O M M E N D A T I O N S I N S TA L L AT I O N R E C O M M E N D AT I O N S The importance of the installation of the Sub-Zero Built-In unit cannot be overemphasized. [. . . ] IMPORTANT NOTE: On all Built-In models, routing, recessing or optional extended handles may be required on raised panels for finger clearance under the handle. Remove the molding using a piece of tape to pull it away from the handle and expose the handle screws. 11 F R A M E D PA N E L I N S TA L L A T I O N M O D E L S 6 8 5 A N D 6 9 5 FRAMED KITS With a Phillips screwdriver, remove the handles from the freezer and refrigerator doors. Be sure the panel is inserted completely into the channel for proper fit and alignment. Replace the trim molding by inserting the top, then the bottom into the handle channel. Release the middle and set the magnets. PA RT I A L F R A M E D A C C E S S O RY K I T If you choose not to use custom wood panels above or below the glasswell for the Model 685 or 695 framed application, a stainless steel insert panel will be provided with the partial framed accessory kit. This accessory kit (part # FRAMPAR), available through your Sub-Zero dealer, includes molding and a stainless steel insert panel for above and below the glasswell on a framed unit. Detailed installation instructions are included with the partial framed accessory kit. PA N E L DESIGN Additional panel design information can be found in the Sub-Zero Design Guide. Check our website at subzero. com. R A I S E D PA N E L S You may have to rout, recess or use optional extended handles with some door panel designs to allow for finger clearance. This is particularly true if your unit has raised panels greater than 1/4" (6) total thickness. IMPORTANT NOTE: The weight of each panel cannot exceed 50 lbs (23 kg). Check the location of offset when you're using specific routing for the grip area only. Refer to the Built-In section of the Sub-Zero Design Guide for a full-scale template of the standard full-length handle and panel. Use this grid template to lay out your panel design for finger clearance when standard full-length handles are used. F R A M E D R E T R O F I T A C C E S S O RY K I T With the framed retrofit accessory kit, existing Model 680 or 690 door panels can be used on a new Model 685 or 695 framed unit. This accessory kit (part # FRAMRET), available through your Sub-Zero dealer, includes moldings and stainless steel insert panels to accommodate existing Model 680 or 690 framed door panels. Detailed installation instructions are included with the framed retrofit accessory kit. Dimensions in parentheses are in millimeters unless otherwise specified. 13 F R A M E D PA N E L S P E C I F I C A T I O N S F R A M E D D O O R PA N E L S All Refrigerator | All Freezer Framed (F) Models F R A M E D D O O R PA N E L S Over-and-Under Framed (F) Models Model 601R Refrigerator Framed Panel W 34 1/8" (867) H 58 15/16" (1497) Model 611 Refrigerator Framed Panel Freezer Framed Panel W 28 1/8" (714) 28 1/8" (714) H 48 1/16" (1221) 18 3/8" (467) Raised Panel Handle Recess Location ­ Refrigerator Panel Model 601RG Refrigerator Framed Panel A) 29 15/32" (749) W 34 1/8" (867) H 58 15/16" (1497) Raised Panel Handle Recess Location ­ Refrigerator Panel Freezer Panel Model 611G Refrigerator Framed Panel Freezer Framed Panel A) 24 1/32" (610) B) 14 1/16" (357) W 28 1/8" (714) 28 1/8" (714) H 48 1/16" (1221) 18 3/8" (467) Raised Panel Handle Recess Location ­ Refrigerator Panel Window Cut-out Dimensions Window Cut-out Location Model 601F Freezer Framed Panel A) 29 15/32" (749) 25 3/8" (645) C) 4 3/8" (111) W 34 1/8" (867) 41 3/16" (1046) D) 13 3/8" (340) H 58 15/16" (1497) Raised Panel Handle Recess Location ­ Refrigerator Panel Freezer Panel Window Cut-out Dimensions Window Cut-out Location Model 650 A) 24 1/32" (610) B) 14 1/16" (357) 19 3/8" (492) C) W 34 1/8" (867) 34 1/8" (867) 4 3/8" (111) 39 5/16" (999) D) 4 3/8" (111) H 48 1/16" (1221) 18 3/8" (467) Raised Panel Handle Recess Location ­ Freezer Panel A) 29 15/32" (749) IMPORTANT NOTE: Panel specifications are for Built-In framed (F) models. Panel specifications for overlay models are on pages 18­19. Refrigerator Framed Panel Freezer Framed Panel Raised Panel Handle Recess Location ­ Refrigerator Panel Freezer Panel Model 650G Refrigerator Framed Panel Freezer Framed Panel A) 24 1/32" (610) B) 17 1/16" (433) W 34 1/8" (867) 34 1/8" (867) H 48 1/16" (1221) 18 3/8" (467) Raised Panel Handle Recess Location ­ Refrigerator Panel Freezer Panel Window Cut-out Dimensions Window Cut-out Location A) 24 1/32" (610) B) 17 1/16" (433) 25 3/8" (645) C) 4 3/8" (111) 39 5/16" (999) D) 4 3/8" (111) C IMPORTANT NOTE: Panel specifications are for Built-In framed (F) models. Panel specifications for overlay models are on pages 18­19. FRAMED PA N E L S Panel specifications are for Built-In framed (F) models. A C C C 14"(356) 14"(356) H 14"(356) H A A D B W W H W B A H C C C 14"(356) H D H W Models 601R and 601F Model 601RG 14 Models 611 and 650 Models 611G and 650G F R A M E D PA N E L S P E C I F I C A T I O N S F R A M E D D O O R PA N E L S Side-by-Side Framed (F) Models PA RT I A L F R A M E D D O O R PA N E L S Ice | Water Dispensing Framed (F) Models Model 661 Refrigerator Framed Panel Freezer Framed Panel W 19 1/8" (486) 14 5/8" (371) H 67 11/16" (1719) 67 11/16" (1719) Model 685 Refrigerator Partial Framed Panel Freezer Partial Framed Panel Model 695 Refrigerator Partial Framed Panel Freezer Partial Framed Panel W 15 5/8" (397) 15 5/8" W (397) H 67 11/16" (1719) 67 11/16" (1719) H Raised Panel Handle Recess Location ­ Refrigerator | Freezer Panel Model 642 Refrigerator Framed Panel Freezer Framed Panel A) 38 5/32" (969) W 24" (610) 15 5/8" (397) H 67 11/16" (1719) 67 11/16" (1719) The partial framed accessory kit (FRAMPAR) is required for this option. Kit includes partial framed molding and classic stainless steel inset handle panels for above and below glasswell on the refrigerator door. 17 15/16" (456) 67 11/16" (1719) 17 15/16" (456) 67 11/16" (1719) Raised Panel Handle Recess Location ­ Refrigerator | Freezer Panel Model 685 Refrigerator Framed Panel Freezer Framed Panel A) 38 5/32" (969) PA N E L G R I L L E O P T I O N W 24" (610) 15 5/8" (397) H 67 11/16" (1719) 67 11/16" (1719) Models 611 and 611G Grille Panel Width (969) 12 7/16" F) H (315) (726) Models 650, 650G, 661 Grille Panel Width Models 642 and 685 Grille Panel Width Model 632 Refrigerator Framed Panel Freezer Framed Panel W 27 11/16" (703) 67 11/16" (1719) 17 15/16" (456) 67 11/16" (1719) Models 632 and 695 Grille Panel Width 10" (254) Grille Raised Panel Handle Recess Location ­ Refrigerator | Freezer Panel Model 695 Refrigerator Framed Panel Freezer Framed Panel A) 38 5/32" (969) W H Grille Panel Height 11" (279) Grille (standard) Grille Panel Height 12" (305) Grille Height Grille Panel Height 13" (330) Grille Grille Panel Height 14" (356) Grille Grille Panel Height 15" (381) Grille IMPORTANT NOTE: Panel specifications are for Built-In framed (F) models. For Models 685 and 695, panel thickness in the glasswell area can range from 1/4" (6) to a maximum of 1 1/8" (29). If the panel is thicker, you must rout out a minimum 1/4" (6) flat landing area to accommodate the bezel surrounding the glasswell. Framed (F) Models W 28 3/16" (716) W 34 3/16" (868) W 40 3/16" (1021) W 46 3/16" (1173) H 8 15/16" (227) H 9 15/16" (252) H 10 15/16" (278) H 11 15/16" (303) H 12 15/16" (329) H 13 15/16" (354) Raised Panel Handle Recess Location ­ Refrigerator | Freezer Panel Glasswell Cut-out Dimensions Glasswell Location (Refrigerator) A) 38 5/32" (150) (39) 5 7/8" E) 1 9/16" 28 9/16" 27 11/16" (703) 67 11/16" (1719) 17 15/16" (456) 67 11/16" (1719) Raised Panel Handle Recess Location ­ Refrigerator | Freezer Panel Glasswell Cut-out Dimensions Glasswell Location (Refrigerator) A) 38 5/32" (969) 5 7/8" (150) E) 1 9/16" (39) 12 7/16" (315) F) 28 9/16" (726) Grille Panel Height For panel grille insert size, use width dimension listed for your model and height dimension for grille option. [. . . ] Once the adjustments are made, tighten the allen head screws--do not put the shipping screws back. Do not drill through the model and serial number plate. 17 1/8"(435) 17 1/8"(435) 17 1/8"(435) 17 1/8"(435) 17 1/8"(435) 17 1/8"(435) 17 1/8" (435) 17 1/8" (435) Illus. 19 21 C O M P L E T I N G T H E I N S TA L L AT I O N 9 0 D E G R E E D O O R S TO P I N S TA L L AT I O N C H E C K L I S T The doors of all Built-In models open to 130 degrees. For Models 601R, 601RG, 601F, 661, 642, 685, 632 and 695, optional 90° or 105° door stop kits are available through your Sub-Zero dealer. Models 611, 611G, 650 and 650G come with a door stop pin to limit the door swing to 90 degrees. [. . . ]