User manual SUB-ZERO 427-PS

[. . . ] ANTI-TIP BRACKET* 13 1/2" (343) (635) 25" (686) 27" (635) 25" LOCATE ELECTRICAL WITHIN SHADED AREA ­ ORIENT GROUND PRONG TO RIGHT AS SHOWN ANTI-TIP BRACKET (2032) 80" 4 1/2" (114) 1/4" (6) 13" (330) 2 1/2" (64) 15 1/2" (394) NOTE: ANTI-TIP BRACKET MUST BE INSTALLED TO PREVENT UNIT FROM TIPPING FORWARD ANTI-TIP BRACKET FRONT VIEW SIDE VIEW DIMENSIONS Finished Rough Opening Width Finished Rough Opening Height Finished Rough Opening Depth Location of Electrical 27" (686) 80" (2032) 25" (635)* Within shaded area *The depth of the Model 427 is 24" (610) from the front of the unit to its back. Your design may necessitate moving the unit back, or cabinets forward to achieve a flush fit. See Installation Instructions shipped with unit for detailed specifications. Dimensions in parentheses are in millimeters unless otherwise specified. 4 Planning Information Wine Storage Model 427 I N S TA L L AT I O N N OT E S Refer to the illustrations and specifications for overall dimensions, finished rough opening dimensions and installation specifics. IMPORTANT NOTE: The depth of Model 427 is 24" (610) from the front of the unit to its back. [. . . ] Locate electrical within the shaded area shown in the installation illustration on page 4. In addition, be aware of local codes and ordinances when installing your service. Refer to the Wine Storage Installation Instructions packed with the appliance, which provides step-by-step procedures for making sure the unit is installed properly. Dimensions in parentheses are in millimeters unless otherwise specified. 5 Planning Information Wine Storage Model 427 I N T E G R AT I N G C A B I N E T RY Unless you are installing a stainless steel unit, you will need to provide a full door panel in the instance of a solid door unit, or a frame for the glass door application, where wine will be seen from the outside. If you order a stainless steel Model 427, you will need to have the stainless steel panel and handle installed. A solid panel must not be installed on a glass door unit, as this may cause moisture to form behind the panel. I N T E G R AT E D PA N E L S If you are familiar with our Integrated line and its panel applications, this section will be relatively easy to understand. The Wine Storage solid door panels or frame panels for glass doors will follow some of the identical planning processes you learned with the Integrated line. Rather than using the mounting hardware we used with the Integrated units, the door panel for Model 427 will be attached with screws applied through our door. IMPORTANT NOTE: The depth of Model 427 is 24" (610) from the front of the unit to its back. You MUST allow for the thickness of the panel you are applying when planning for the finished rough opening depth if you want the front panel to be flush with surrounding cabinetry. You may have to move the unit back into drywall or bring the cabinets forward. The glass door opening of the standard Model 427 is designed to be exposed to room air circulation. While the cabinet front stiles are a minimum of 2 1/4" (57), the top and bottom rails are different. Rails and stiles can be increased in size but should not exceed cabinet manufacturers standard width. They cannot exceed overall door panel dimensions specified, as they would interfere with the operation of the door. The back sides of rails and stiles that will be visible through the glass door will need to be finished. Also, the inside edges of the frame must be finished to match the front surface. Dimensions in parentheses are in millimeters unless otherwise specified. 6 Planning Information Wine Storage Model 427 I N T E G R AT E D PA N E L S IMPORTANT NOTE: Wine Storage models with a solid door are available as a special order and require 90 days for delivery. The dimensions of these panels and stiles are assuming the Model 427 finishes off at 80" (2032) in height overall and has a 4" (102) toe kick. If you finish off at 84" (2134) for instance, you must add 4" (102) additional to the overall height of the panel and remember to add 4" (102) to the top rail. Dimensions in parentheses are in millimeters unless otherwise specified. 8 Planning Information Wine Storage Model 427 F R A M E D C A B I N E T RY A P P L I C AT I O N S FRAMED CABINETRY Framed cabinetry applications present you with different questions to address. The illustrations on this page show common applications of framed cabinetry. These are not meant to be the only alternatives, but are suggestions from designers around the country. Also refer to the full-scale illustrations at the end of this section for specifics on door openings. IMPORTANT NOTE: The depth of the Model 427 is 24" (610) from the front of the unit to its back. [. . . ] If you choose to stain or seal the wood facing, be aware that some of these substances are hazardous and will damage stored wine. Dimensions in parentheses are in millimeters unless otherwise specified. 12 Planning Information Wine Storage Model 427 WINE STORAGE DOOR FRAME Glass C L Cabinet Door Profile 7/8" (22) 7/8" (22) 2 1/4" (57) Rail / Stile DOOR FRAME PROFILE F U L L - S C A L E T E M P L AT E The full-scale illustrations on this page and the following page enables you to understand some of the unique situations you may face as you design the Wine Storage units into homes. These templates can be easily photocopied or used in your tracings. The full-scale illustration above is typical of the Model 424 door frame profile, details of the other Wine Storage door frames will vary slightly. IMPORTANT NOTE: Rails and stiles must be wide enough to cover the door hinges. The back sides of rails and stiles that will be visible through the glass door will need to be finished. Dimensions in parentheses are in millimeters unless otherwise specified. 13 Planning Information Wine Storage Model 427 WINE SHELF WOOD FACING 5/8" (16) 7/64" (3) Maximum Thickness 11/2" (38) 27/32" (21) 5/64" (2) 2015/16" (532) WIDTH 23/64" (9) 9/16" (14) FRONT VIEW SIDE VIEW F U L L - S C A L E T E M P L AT E Use the full-scale illustration above as a template if you choose to replace the natural cherry wood facing with wood more complementary to your design and surrounding cabinetry. Dimensions in parentheses are in millimeters unless otherwise specified. 14 Planning Information Wine Storage Model 427 SUB-ZERO DOOR FRAMED CABINETRY IMPORTANT NOTE: The depth of the Model 427 is 24" (610) from the front of the unit to its back. Your design may necessitate moving the unit back, or cabinets forward to achieve a flush fit. T 24 (610) TO BACK OF UNIT LINE OF INTERFERENCE* LINE OF INTERFERENCE* AT MAXIMUM DOOR OPENING 1 (3) MIN. [. . . ]