User manual SUB-ZERO 400UC

[. . . ] W INE S TORAGE USE & CARE INFORMATION CONTENTS Sub-Zero Wine Storage Sub-Zero Wine Storage Features Sub-Zero Wine Storage Models Sub-Zero Wine Storage Use & Care Keeping Wine at Its Best Troubleshooting Guide Service Information Sub-Zero Warranty 3 4 5 8 18 20 22 23 As you read this Use & Care Information, take particular note of the CAUTION and WARNING symbols when they appear. This information is important for safe and efficient use of the Sub-Zero equipment. signals a situation where minor injury or product damage may occur if you do not follow instructions. states a hazard that may cause serious injury or death if precautions are not followed. In addition, this Use & Care Information may signal an IMPORTANT NOTE which highlights information that is especially important. SUB-ZERO ® is a registered trademark of Sub-Zero Freezer Company, Inc. S U B - Z E R O W I N E S TO R AG E T H A N K YO U Thank you for purchasing your new Sub-Zero Wine Storage unit. The ultimate in beauty, engineering, detailing and functionality, this Wine Storage equipment continues the Sub-Zero tradition of superior quality and reliability, giving you the peace of mind that your wine is stored properly, at the exact temperature you select. Your Sub-Zero Wine Storage model is protected by a warranty that is one of the finest in the industry. [. . . ] Watch that fingers are not placed in the door opening on the hinge side when the door is open. Model 430: An optional 90° door stop is available as a sales accessory. Contact your Sub-Zero dealer for details. 90° Door stop ­ Models 427 and 427R 14 S U B - Z E R O W I N E S TO R AG E U S E & C A R E CLEANING S TA I N L E S S S T E E L E X T E R I O R Classic and platinum stainless steel finishes: To clean the exterior of the classic and platinum stainless steel finishes, use a soft, nonabrasive stainless steel cleaner like Signature Polish and apply with a soft 100% lint-free cloth. Carbon stainless steel finish: Carbon stainless steel can be cleaned with mild soap and water. The carbon stainless steel finish uses the interest of brushed steel to bring out the maximum metallic luster of its charcoal background. Different light types and source locations can result in variations in shading on different components and areas of large appliances. These variations are normal with the carbon finish and add to the unique character of colored stainless steel. To bring out the natural luster of all three finishes, lightly wipe the surface with a waterdampened microfiber cloth followed by a dry polishing chamois. Better results are obtained by keeping the cloth in continuous contact with the stainless steel. GLASS DOOR CLEANING The glass door panel can be cleaned using any standard glass cleaner available on the market today. S I G N AT U R E POLISH Signature Polish is available from Signature Limited Laboratory, P. Box 13436, Dayton, Ohio 45413-0436, or 877-376-5474 (toll free). INTERIOR CLEANING To clean interior surfaces and removable parts, wash with a mild solution of soap and lukewarm water with a little baking soda. Avoid getting water on lights, control panel and the solid cherry wood facing on the shelves. Do not use abrasive cleaners or cloths on any of the interior or exterior surfaces, including the glass door panel. Before cleaning the unit, shut the electricity off at the control panel. Under no circumstances should you use a metallic or highly abrasive cleaner or cloth, as this will remove the carbon finish or scratch the classic or platinum finishes. 15 S U B - Z E R O W I N E S TO R AG E U S E & C A R E CLEANING CONDENSER CLEANING Clean the condenser area every three to six months. The cleaning schedule will depend on the amount of dust and lint that accumulates in this area. To access the condenser on your specific Wine Storage model, see Condenser Location. Use a soft bristle brush and vacuum hose to remove dust and lint from the condenser area. NOTE: To avoid bending the condenser fins, be sure to vacuum in the direction of the fins (up and down). C O N D E N S E R L O C AT I O N Models 424 and 424FS: On these models the condenser is located behind the kickplate. Models 427 and 427R: On these models the condenser is located behind the kickplate / grille. This assembly will slide forward easily, giving you access to the condenser area. Model 430: The condenser is located behind the grille at the top of the unit. To remove the louvered grille, first open the door to access three Phillips head screws. Tilt the grille forward at the top and release the springs from behind the grille, and then lift off the grille. To remove a panel grille on Model 430, lift the grille up, then pull out at the bottom and down to release it from its mounting bracket. Before cleaning the condenser, shut the electricity off at the control panel. [. . . ] Model Number Serial Number Installation Date Sub-Zero Authorized Service Center and Phone Sub-Zero Dealer and Phone B E F O R E C A L L I N G F O R S E RV I C E Before calling a Sub-Zero authorized service center, refer to the Troubleshooting Guide on pages 20­21. Check the household fuse or circuit breaker to see if it has been blown or tripped and that the electrical connection to the appliance has not been disconnected. A power outage may also have caused a disruption in service. The information and images in this guide are the copyright property of Sub-Zero Freezer Company, Inc. Neither this book nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Sub-Zero Freezer Company, Inc. [. . . ]