User manual SUB-ZERO 400 INSTALL GUIDE

[. . . ] W INE S TORAGE INSTALLATION INSTRUCTIONS S U B - Z E R O W I N E S TO R AG E The importance of the installation of the Sub-Zero Wine Storage unit cannot be overemphasized. CONTENTS Models 424 and 424FS Installation Models 427 and 427R Installation Model 430 Installation Installation Checklist Service Information 3 12 24 34 35 Before you begin the installation process, it is recommended that you read this entire Installation Instructions book. There are key details that you should take special care to observe during the installation. By reading these instructions carefully, you will make the installation process easier, problem-free and, most importantly, safe. [. . . ] Additional panel information can be found in the Sub-Zero Design Guide. PA N E L DESIGN Additional panel design information can be found in the Sub-Zero Design Guide. 9 Dimensions in parentheses are in millimeters unless otherwise specified. 19 M O D E L S 4 2 7 A N D 4 2 7 R I N S TA L L AT I O N MODELS 427 | 427R S TA I N L E S S S T E E L D O O R P A N E L OV E R L AY G L A S S D O O R P A N E L Inspect the door panel for the minimum 5/8" (16) thickness, the greater width requirements for the stiles (to cover the door hinges), and the finished inside edge. See the Wine Storage section of the Sub-Zero Design Guide for additional panel information. Decide if the handle will be attached through the glass door frame or just through the decorative door panel. If it is just through the door panel, the handle must be attached first. If a lock is to be used, the body of the lock should be installed on the door panel after the panel is mounted. Decorative panels are attached to the Model 427 and 427R door using #8 x 5/8" square drive screws passing through the door frame from the rear, behind the gasket into the panel. The door panel is marked for screw locations by the use of `tenon centers', which are temporarily inserted into the 1/4" (6) diameter holes in the front of the glass door frame. Refer to illustration 11 below. Before installing the stainless steel door panel, check the panel carefully. Options are available for kickplate / grille height, overall height, door swing and door lock. PA N E L DESIGN Additional panel design information can be found in the Sub-Zero Design Guide. Check our website at subzero. com. The stainless steel panel is mounted to the door by passing the #8­32 x 5/8" screws provided, through holes in the door frame from the rear, and into the threaded holes in the door panel. The screw holes inside the door are hidden under a cover flap on the door gasket. After the door panel is installed, apply the cover tape patches provided, over the holes on the inside surface of the door. For installation of stainless steel panels on Model 427R drawers, see Model 427R Drawer Panels on page 22. The cover plugs or patches are part of the insulation system on the door of the Wine Storage unit. Be sure to cover all the holes in the door that were used. Gasket 13/32" (11) Diameter Stainless Steel Panel Door Frame Glass Integrated Panel Door Frame 1/4" (6) Diameter Back of Stainless Steel Panel Illus. 11 20 M O D E L S 4 2 7 A N D 4 2 7 R I N S TA L L A T I O N MODELS 427 | 427R With the Wine Storage unit secured in position and the door closed, the panel is held in the desired position on the door and rapped by hand from the front, putting center marks on the rear surface of the panel. If the door panel is made of such a material that pre-drilling is needed, all of the mounting holes should be marked. If not, only enough holes to hold the panel in place temporarily, are necessary. The door panel is then lowered from the door frame, tenon centers removed, the door opened and the screws driven into the panel through the black tape on the door frame, using the center marks to locate the screws. The screw holes inside the door, are hidden under a cover flap on the door gasket. [. . . ] You can also visit our website at subzero. com. Do not drill through the model and serial number plate. Illus. 16 33 M O D E L 4 3 0 I N S TA L L A T I O N I N S T R U C T I O N S M O D E L 430 HINGE A D J U S T M E N T I N S TA L L AT I O N C H E C K L I S T IMPORTANT NOTE: The unit must be installed and leveled before adjusting the door hinges. If not, adjust the top or bottom door hinge by first removing and discarding the two small shipping screws. Adjust the top hinge left to right and in or out by loosening the three allen head screws. [. . . ]