User manual SUB-ZERO 315W

[. . . ] MODEL 315W WINE COOLER INSTALLATION & OPERATION CONTENTS Model 315W Features Model 315W Installation Installation Checklist Model 315W Operation Troubleshooting Guide Service Information Sub-Zero Warranty 4 5 13 14 17 18 19 Features and specifications indicated herein and on the website are subject to change at any time without notice. Check our website, subzero. com, for the most up-to-date specifications. As you follow these instructions, you will notice WARNING and CAUTION symbols. This blocked information is important for the safe and efficient installation of Sub-Zero equipment. There are two types of potential hazards that may occur during installation. signals a situation where minor injury or product damage may occur if you do not follow instructions. states a hazard that may cause serious injury or death if precautions are not followed. Another footnote we would like to identify is IMPORTANT NOTE: This highlights information that is especially relevant to a problemfree installation. SUB-ZERO ® is a registered trademark of Sub-Zero Freezer Company, Inc. S U B - Z E R O M O D E L 3 1 5 W I N S TA L L AT I O N A N D O P E R AT I O N T H A N K YO U Congratulations on the purchase of your Sub-Zero Model 315W wine cooler. [. . . ] If it is just through the door panel, the handle must be attached first. The screw holes inside the door, are hidden under a cover flap on the door gasket. Use as many screws as necessary to hold door panel in place properly. IMPORTANT NOTE: After the first three or four mounting screws are in place, but not completely tightened, close the door and check your panel fit. Once you are satisfied with the appearance, open the door and apply the remainder of the screws. The metal frame on the glass door has numerous mounting holes on each side of the door. This is to accommodate the Sub-Zero accessory handles and provide for easy attachment of the handle through the door frame. The illustration below shows how the holes pass through the door frame. The hole center is on the small locator groove in the front of the frame. A 1/4" (6) diameter hole is made in the front wall of the extrusion and a 13/32" (11) diameter hole through the rest of the frame. Exercise caution when drilling holes for mounting the panel to the door frame. Gasket Overlay Panel Door Frame 13/32" (11) Diameter Glass 1/4" (6) Diameter Tenon Center Overlay door panel Door frame cross-section 11 S U B - Z E R O M O D E L 3 1 5 W I N S TA L L AT I O N OV E R L AY PA N E L I N S T A L L A T I O N IMPORTANT NOTE: Install screws in all the mounting holes in the door frame. The nature of the door panel with a narrow outer rim and no connecting center member requires the support provided by the glass door. PA N E L DESIGN Additional panel design information can be found in the Sub-Zero Design Guide. Check our website at subzero. com. After the door panel installation is complete, apply the cover patches or plugs provided over the holes on the inside surface of the door. The wine cooler door is made with a sealed double wall tempered glass core. Be sure the hole is centered on the small groove in the front of the door frame and the drill passes squarely through the frame. If you are inexperienced with drilling, fasten the handle from the rear of the door panel only. The cover patches or plugs are part of the insulation system on the door of the wine cooler. Be sure to cover all the holes in the door that were used. 12 S U B - Z E R O M O D E L 3 1 5 W I N S TA L L AT I O N I N S TA L L AT I O N C H E C K L I S T IMPORTANT NOTE: To ensure a safe and proper installation, the following checklist should be completed by the installer to ensure that no part of the installation has been overlooked. Any questions or problems about the installation should be directed to your Sub-Zero dealer or the Sub-Zero Customer Service Department at 800-222-7820. Has the unit been properly uncrated, and have all packing materials and tape been removed from inside the product?Have any installation or service problems been noted on the product registration card?Instruct the owner to register the product. If you are storing or disposing of your old refrigerator or freezer, please do it safely. Child entrapment accidents can be tragic. C O N TA C T I N F O R M AT I O N Sub-Zero Customer Service: 800-222-7820 Website: subzero. com 13 S U B - Z E R O M O D E L 3 1 5 W O P E R AT I O N USING YO U R W I N E C O O L E R Your wine cooler is extremely simple to use, just turn the control knob to the ON position. The Model 315W will automatically begin to cool and will continue to do so until the set temperature is reached. The Model 315W operates on this principal; the unit will run to achieve the set temperature. [. . . ] Your registration information will allow us to send you exciting new product updates and recipes as they become available, along with information on special events. Sub-Zero Dealer and Phone B E F O R E C A L L I N G F O R S E RV I C E Before calling a Sub-Zero authorized service center, refer to the Troubleshooting Guide on page 17. Check the household fuse or circuit breaker to see if it has been blown or tripped and that the electrical connection to the appliance has not been disconnected. A power outage may also have caused a disruption in service. The information and images in this guide are the copyright property of Sub-Zero Freezer Company, Inc. Neither this book nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Sub-Zero Freezer Company, Inc. [. . . ]