User manual STUV 30-IN

[. . . ] ­ An oversized chimney can be as harmful to the proper operation of the fireplace as one that is too small. ­ The ideal solution is a flue constructed inside the building and thermally insulated. 3 Allen key ­ a 13 mm openend spanner ­ 8mm openend spanner ­ 1 small and 1 large flatblade screwdriver ­ a spirit level ­ a claw hammer ­ a trolley ­ a blanket or a piece of wood Using the claw hammer, remove the wooden packing that protected the fireplace during transport (photo 7). To make your work easier, you could unpack it and remove the components located in the combustion chamber and, perhaps, also remove the three doors. [. . . ] Make it airtight by filling the space between the pipe and the flange. Note : once the fireplace is in its final position, don't forget to remove the transport and positioning bracket (photo 25). We strongly recommend that you connect these, if you are not using a ventilator to distribute the hot air. Remove the precut parts by tapping as closely as possible to the smoke outlet, and then screw in the flanges (photos 26 & 27). 36 Place the four levels of vertical refractories from left to right; cover the bottom of the fireplace with the five remaining refractories. 37, 38 and 39 It is easy to position the deflector on the refractories, thanks to the lugs, which perfectly match their shape. De ventilator in de opening van de aslade steken, de kabels door de opening rechts onderaan trekken (fig. Check that the delivery does in fact include the following items (photo 44): ­ 1 ventilator, ­ 2 foamrubber seals, ­ 1 "switch" housing, ­ 2 M5x8 fixing screws for the "switch" housing. Using the 8mm box spanner, remove the 2 screws from the ventilator access hatch panel (photo 48). Stick the 2 foamrubber seals on either side of the circular hole, perpendicular to the back wall, in such a way that the ventilator can be put in place (photo 50). Position the ventilator in the ashpan space, and pass the cables through the hole (Figure 52A) at the back on the right (photo 51). Rotate it a few degrees so that it fits snugly into the recess (Figure 52). Insert the "switch" casing, with the speed regulator uppermost (photo 55). Reconnect the power supply, and test the ventilator's operation in all three positions. You have chosen a Stûv fireplace ; Concept & Forme thanks you for doing so. This fireplace was designed to offer you maximum pleasure, comfort and safety. We recommend that you should : ­ entrust its installation (or at any rate its inspection) to a skilled professional, ­ carefully read these directions for use and comply with the cleaning instructions, ­ duly fill in the certificate of guarantee and return it to us, while clearly mentioning the manufacturer's no. , which can be seen on the main frame of the appliance, in the middle, above the ashpan in the sold door position (photo 2), ­ have the flue swept at regular intervals (once a heating season, for regular use) in order to ensure optimum operation and maximum safety. ­ The paint is not ovenbaked and it is therefore relatively fragile but will harden when it is heated for the first few times. Consequently, take care when handling the appliance when it is being fitted. ­ A paint spray supplied with the appliance allows you to touch up the paintwork, if necessary. ­ When lighting the fire for the first time, some unpleasant smoke or smells may be released. [. . . ] The exchange of parts under guarantee does not extend the duration of the initial guarantee. This document must have been returned to us, duly filled in, within one month following the date of the invoice from the vendor to the buyer. The information contained in this box will only be used in case of a problem, to help the customer. The manufacturer is not bound to notify any nonconformity of the installation at the time of this document's receipt. [. . . ]