User manual STRYKER TPS 5100-52

[. . . ] IMPORTANT INFORMATION: File this in your TPS records Total Performance System Console REF 5100-1 and 5100-2 Irrigation Console REF 5100-50 and 5100-52 TPS Console 5100-1, 5100-2, 5100-50, and 5100-52 User's Guide ······················ Includes setup, safety, repair, and warranty information for the Stryker Total Performance System. For answers to questions about other equipment, see the information supplied with that equipment. 4100 E. 1-800-253-3210 European Authorized Rep: 1-616-323-7700 RA/QA Manager Fax 1-800-999-3811 Stryker BP 50040-95946 Roissy CDG France Phone: 33-1-48-17-50-00 1 © 1998, Stryker Corporation 2 Contents Software License Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Where to Find Answers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Power: Use with the increase and decrease icons to adjust saw power. System Options Options: Gives access to handpiece adjustments, system information, console controls and user preference. Handpiece option: Accesses corresponding handpiece adjustment screens. Forward (clockwise) Variable: Handpiece speed responds to varying degrees of pressure on the footswitch or handswitch. Nonvariable: Handpiece operates at constant set-point speed/power level. One touch: Handpiece is activated by one touch of a trigger device and continues to run when the trigger device is released. In this mode, the handpiece operates at constant set-point speed/power level. Reverse (counterclockwise) Information: Displays system information screen. Oscillate Console: Gives access to console adjustment screen. Irrigation: Activates or deactivates handpiece irrigation. Allows access to the surgeon preference screen. NOTE: TPS Console models REF 5100-1 and 5100-2 will not display options related to handpiece irrigation. Advanced: - Accesses the advanced footswitch mapping screen. Button: Access button mapping screen. Return to full screen: Return from large to full handpiece screen. 11 Saw Handpiece Screen TPS Oscillating and Sagittal Saws POWER/WATER ADJUSTMENT The power icon functions as a toggle switch for power and water settings. Power and irrigation adjustments are made using the adjustment arrows. As the power setting is reduced from 100%, a vertical bar displays to correspond to the lower selected maximum power. This screen appears when a TPS saw is selected at the TPS1 port with the maximum power set at 100%. ENDO, TPS2 and the footswitch icons indicate other instruments are plugged into the console. The irrigation setting is not displayed on this screen. However, it can be seen on the Handpiece Adjustments screen. METHOD OF OPERATION Saws can be operated with the TPS Universal Handswitch or TPS Footswitch. Handswitch Handpiece selection can be made by depressing the handswitch once. Footswitch Handpiece runs from start-up to the maximum selected speed with either the forward or reverse pedal. 12 Rotary Handpiece Screen SPEED/WATER ADJUSTMENT The speed icon functions as a toggle switch for speed and water settings. Speed and irrigation adjustments are made using the adjustment arrows. DIRECTION OPTIONS FORWARD Clockwise REVERSE Counterclockwise This screen appears when a TPS rotary handpiece is selected. The TPS Universal Drill is plugged into the TPS2 port and the speed is set at 75, 000 RPM. ENDO, TPS1 and the footswitch icons indicate that other instruments are plugged into the console. TPS MicroDriver METHOD OF OPERATION The TPS MicroDriver can be operated with its built-in trigger and rotary control switch or with the TPS Footswitch. NOTE: The handpiece will not run when the rotary switch is in the SAFE position. Trigger The built-in speed control trigger runs the handpiece from start-up to the maximum selected speed. Footswitch Handpiece runs from start-up to the maximum selected speed. The direction icon on the screen changes when the corresponding footswitch pedal is depressed. Example: If the footswitch reverse pedal is depressed while the handpiece rotary switch is set in forward, the handpiece operates in the reverse direction and the reverse icon highlights. However, after the pedal is released, the direction icon will revert to the direction set on the rotary switch. TPS Universal and Micro Drills METHOD OF OPERATION The Universal Drill can be operated with the TPS Universal Handswitch or TPS Footswitch. Handswitch Handpiece selection can be made by depressing the handswitch once. Speed and cutting direction corresponds to what is selected on the screen. [. . . ] Contact Stryker Customer Service at 1-800-253-3210 to request a loaner. Send the inoperative unit to Stryker with a purchase order number of authorization for repair. Also, provide a name and address for shipping the repaired instruments. Return the inoperative unit to: Stryker Instruments Repair Department 4100 E. [. . . ]