User manual STAIRVILLE DMX512

[. . . ] If you sell the unit to another user, be sure that they also receive this instruction booklet Unpack and check carefully there is no transportation damage before using the unit. Before operating, ensure that the voltage and frequency of power supply match the power requirements of the unit. It's important to ground the yellow/green conductor to earth in order to avoid electric shock. The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces. [. . . ] (Resistance 120 ohm 1/4W) between pin2 (DMX-) and pin3 (DMX+) of the last fixture. 1 3 2 1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin adapter-cable. Solder a 120 ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in the DMX-output of the last unit. Connect the unit together in a `daisy chain` by XLR plug from the output of the unit to the input of the next unit. Inadequate or damaged cables, soldered joints or corroded connectors can easily distort the signal and shut down the system. The DMX output and input connectors are pass-through to maintain the DMX circuit, when power is disconnected to the unit. Each lighting unit needs to have an address set to receive the data sent by the controller. The address number is between 0-511 (usually 0 & 1 are equal to 1). The end of the DMX512 system should be terminated to reduce signal errors. 3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+) 5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+) 5. 4. Lamp In case of replacement of the lamp or maintenance, do not open the CHANNEL 5 TILT 270° DMX512 CONFIGURATION CHANNEL 1 SHUTTER 255 CHANNEL 2 GOBO 255 Fast CHANNEL 3 COLOR 255 Fast CHANNEL 4 PAN 540° fixture within 15 minutes until the unit cools down after switching off. Lamp : ELC 24V 250W 196 Gobo Shaking 1. Always switch off the main supply and never handle the lamp or luminaries when is hot. If this happens, clean the lamp with denatured Slow Slow alcohol and wipe it with a lint free cloth before installation. Make sure the lamp is located in the center for the best spot. 136 Gobo/Color 128 120 112 104 96 88 80 72 64 56 48 40 32 24 16 8 0 92 Color 16 0 GOBOS Gobo Stopped Gobo 14 Gobo 13 Gobo 12 Gobo 11 Gobo 10 Gobo 9 Gobo 8 Gobo 7 Gobo 6 Gobo 5 Gobo 4 Gobo 3 Gobo 2 Gobo 1 Open Blackout 128 121 110 99 88 77 66 55 44 33 22 11 0 Magenta Yellow Blue Light green Pink UV Purple Red Amber Light blue Orange Green White 0° 0° Diagram for Lamp changing 6B 1 2 3 4 5 6 7 8 9 10 11 12 13 14 4. How To Set The Unit 4. 1 Control Panel 5. 2 Easy Controller The easy remote control is used only in master/slave mode. By connecting to the 1/4" microphone jack of the first unit, you will find that the remote control on the first unit will control all the other units for Stand by, Function and Mode. FUNCTION : Under FAST mode, the light will strobe in three different ways: a. ) Strobe in different gobos and colors. If the unit in slow mode, press NEXT button to choose desired color 1. Button MENU DOWN UP ENTER to select the programming functions to go backward in the selected functions to go forward in the selected functions to confirm the selected functions On On On Flashing DMX input present master mode slave mode sound activation and gobo. The unit's movement- Pan/Tilt & Gobo/Color is sound activated. [. . . ] To go back to the functions without any change press the MENU button again. Fixture Hours Press the MENU button up to when the is blinking on the display. Pressing ENTER button and the display will show the number of working hours of the unit. To go back to Tilt Inversion Press the MENU button up to when the is showing on the display. Pressing the functions press the MENU button again. ENTER button and the display will blink. [. . . ]