User manual STAIRVILLE DMX MASTER I

[. . . ] Make sure there is no flammable materials close to the unit while operating as it is fire hazard. Don't handle the unit by taking its head only, but always by taking its base. Don't touch the housing bare-hand during its operation, and allow about 15 minutes to cool down before replacing bulb or serving, as the unit could be very hot. l In the event of serious operating problem, stop using the unit immediately. [. . . ] The stepper motor might be damaged or the cable connected to the PCB is broken. Warning l l l l l l To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture. Do not start on the unit without bulb enclosure or housing are damaged. The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged. Do not look directly at the light while the bulb is on. Caution There are no user serviceable parts inside the unit. In the unlikely event your unit may require service, please contact your nearest dealer. Installation The unit should be mounted via its screw holes on the bottom of the base. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 15 kgs for each unit. 2. Technical Specification Power supply - AC 120V~60Hz - AC 230/240/250V~50/60Hz Lamp - ELC 24V 250W Optical system - Standard 15° focused beam angle. Gobo wheel - Independent gobo wheel with 14 gobos plus open and shutter. Color wheel - Independent color wheel with 11 dichroic mirrors plus white. If the LED on, it is in SLOW mode, Pan/Tilt is sound activated but Gobo/Color wheel are static, controlled by Next button. 7B 5. 3 Universal DMX Controller If you use a universal DMX controller to control the units, you have to set DMX address from 1 to 512 channel so that the units can receive DMX signal. Once the address has been selected, press and keep ENTER button pressed up to when the display stops blinking or storing automatically 8 seconds later. To go back to the functions without any change press the MENU button again. Please refer to the following diagram to address your DMX MASTER I channel for the first 4 units. 4. Remote controller input By connect to the 1/4" microphone jack to control the unit for Stand by, Strobe/Next and Fast/Slow function. DMX input/output For DMX MASTER I link, use 3-pin XLR plug cable to link the unit together. 5. By universal DMX controller No need to turn the unit off when you change the DMX address, as new DMX address setting will be effected at once. Every time you turn the unit on, it will show AE-4 on the display and move all the motors to their `home' position and you may hear some noises for about 20 seconds. After that the unit will be ready to receive DMX signal or run the built in programs. 4. 2 Main Function To select any of the given functions, press the MENU button up to when the required one is showing on the display. Once the required mode has been selected, press the ENTER button to setup or it will automatically return to the main functions without any change after idling 8 seconds. The main functions are showing below: DMX MASTER I Address Setting Show Mode " Show 1 " Show Mode " Show 2 " Slave Mode " Normal " Slave mode " 2 Light Show 2 " Pan Normal Pan Inversion Tilt Normal Tilt Inversion Display Normal Display Inversion Focus Adjust 5. 1 Master/Slave Built In Preprogrammed Function By linking the units in master/slave connection, the first unit will control the other units to give an automatic, sound activated, synchronized light show. [. . . ] Pressing ENTER button and the unit will run self-test by built in program. To go back to the functions press the MENU button again. ENTER button and the display will blink. Use DOWN and UP button to select the (normal) or (pan inversion) mode. Once the mode has been selected, press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds. [. . . ]