User manual SPYDER ELECTRA

[. . . ] Kingman recommends that the customer be at least 18 years of age to purchase this product. Any modifications or tampering of original factory parts will void all warranties and liabilities from Kingman. Kingman recommends using a barrel blocking device when the marker is not in operation. To ensure proper adjustment of velocity Feet Per Second (fps), Kingman strongly recommends using a chronograph for paintball use located at most paintball stores and paintball fields. [. . . ] STEP 1 Loosen the Regulator Adjuster Lock Screw located on the on the Regulator Adjuster Knob. STEP 2 Using the Open End Wrench provided with the spare parts kit, turning the adjuster knob clockwise will decrease the regulator output pressure and turning the adjuster knob counter clockwise will increase the output pressure of the regulator. The regulator output should be no less than 300psi or at least one and a half turn counter clockwise of the Regulator Adjuster Knob from the bottom of the regulator. NOTE: Too low of an output setting from the regulator will result in very low velocity and some recocking issue with the marker. You must have adequate output air pressure from the regulator to avoid starving the marker for air. Too high of an output setting of the regulator will result in excessive air consumption and poor air efficiency. This may also result in dangerously high velocities exceeding the recommended safety limits for playing paintball. STEP 3 After each adjustment to the regulator, you must fire the marker a few times to let the regulator settle to its new output setting. STEP 4 Securing the Regulator Adjuster Lock Screw will prevent the adjuster knob from turning due to vibrations keeping the regulator output setting stable and locked. IMPORTANT: Any adjustment to the inline regulator output pressure will affect the markers velocity setting, always chronograph the marker after each adjustment. NOTE: The Fast Charge Inline Regulator is tuned from the factory to have an output pressure of approximately 350 psi. When adjusting the Regulator to “Decrease” the output pressure, you will need to fire the marker a few times to get the new setting. IMPORTANT: (Make sure you have your marker pointed in a safe direction and you are following all safety guidelines set with the use of this product. ) IMPORTANT: Markers that are equipped with regulators may store residual air after the Compressed Air Tank has been removed. To fully remove any residual air stored in the marker, turn the C/A On/Off adapter knob counter-clockwise to shut off the air supplied from the tank. IMPORTANT: Do not attempt to service the regulator unless you have received proper training from a qualified Kingman Group service technician. Doing so will VOID all regulator warranties and liabilities from Kingman Group. If you experience any leaks or problem with the regulator, contact Kingman Group Technical Support Service Department. IMPORTANT: Always remove all paintballs and C02 / Compressed Air Tank from your marker and remember to keep the marker in its un-cocked position before placing it in storage. HELPFUL TIP: Make sure to have the C02 / Compressed Air Tank filled before use. € • • • Firmly, hand tighten the CO2 / Compressed Air Tank clockwise into the markers C/A On/Off adapter. Tighten the tank clockwise in the markers C/A On/Off adapter until it is snug. [. . . ] 5 80 Piston Shaft O-ring #08 80pu Spare Parts Kit Electra w/Eye Receiver (polished black) REC029 REG003 REG004 REG008 REG009 REG010 REG011 REG012 REG013 REG014 REG028 REG029 RPN001 RPN002 SCR002 SCR003 SCR007 SCR011 SCR025 SCR026 SCR027 SCR028 SCR029 SER001 SPR004 SPR009 SPR013 STB002 STF001 STK008 STP028 STP029 TRF009 TRS008 VBT003 VBT004 VBT008 VBT013 VRT028 VRT029 VTA028 VTA029 WRH002 WRH007 WRH008 Electra w/Eye Receiver (polished titanium) Reg Piston Reg Spring Reg Top Body (polished black) Reg Top Body (polished titanium) Reg Mid Body (polished black) Reg Mid Body (polished titanium) Reg Adjuster (polished black) Reg Adjuster (polished titanium) Reg O-ring Housing (F) Regulator (complete) (polished black) Regulator (complete) (polished titanium) Sear Roll Pin Trigger/Touch Switch Roll Pin M4 x 8 Screw (A) Circuit Board Screw (+) M8 x 8 Valve Body Screw (A) Coil Set Screw M4 x 4 Reg Screw (A) M4 x 10 Reg Adjuster Screw (A) M5 x 20 Vertical Screw (A) M5 x 10 Trigger Frame Screw (A) M4 x 6 Trigger Adjustment Screw (A) Sear Striker Spring ESP Sear Spring Valve Spring Striker Bolt Striker Buffer Top Cocking Knob Striker Plug Threaded (polished black) Striker Plug Threaded (polished titanium) Electronic Trigger Frame (M) Magnetic Saber Trigger (polished black) Delrin Bolt Locking Bearing Delrin Bolt Locking Spring Delrin Bolt w/ Locking Knob Delrin Bolt Locking Screw Vertical Adapter (polished black) Vertical Adapter (polished titanium) Velocity Adjuster & Spring Guide (polished black) Velocity Adjuster & Spring Guide (polished titanium) Battery Harness Touch Switch (3P) Eye Wire Harness ELECTRA w/Eye SCHEMATICS STP028 STP029 ORG002 STF001 SCR029 ORG008 VTA028 VTA029 TRS008 SPR004 STK008 VBT008 STB002 BLS009 BLS010 BLS003 SCR002 ORG001 BLS011 BLS012 BLS014 BLS015 SCR028 REC028 REC029 SER001 WRH008 HSF009 FND019 FND020 ORG002 ORG003 ITP018 ORG023 VRT028 ORG002 VRT029 ITP017 ITP012 HSE010 ITP011 ORG003 BAR028 BAR029 SPR013 ORG002 REG028 REG029 LPC028 LPC029 REG012 REG013 HSF004 HSF009 Charging Port CAMD Display UPPER Button ELM008 LOWER Button RPN002 WRH007 RPN001 SCR011 ELM001 ELM002 ELM004 VBT013 VBT004 VBT003 SCR003 ECB008 ELM003 SCR003 ASA013 SCR002 ORG018 FND028 FND029 SCR007 GRP005 SCR028 TRF009 SCR027 ASA010 ASA014 ITP019 ASA028 ASA029 ASA018 ASA012 HSF001 17 * Item Not Pictured (+) Cross-head Screw (A) Allen-head Screw 18 WARRANTY STATEMENT Kingman warrants the original retail purchaser that this product is free from defects in material and workmanship under normal use and service for a period of (1) year from the original date of purchase. Any Electronic Components in an Electronic Spyder marker are warranted for (6) months from the original date of purchase. Kingman agrees to repair or replace (at its discretion) any product within (a reasonable period of time). 6v rechargeable battery, charger, scratches, nicks, normal wear and tear of parts, any modifications, normal fading of anodizing and damage caused by dropping or hitting of products. [. . . ]