User manual SOYO SY-7VBA 133

[. . . ] SY-7VBA 133 Motherboard **************************************************** Pentium® III & Celeron Processor supported VIA 693A AGP/PCI Motherboard 66/100/133 MHz Front Side Bus supported ATX Form Factor **************************************************** User's Manual SOYOTM Copyright © 2001 by Soyo Computer Inc. SY-7VBA 133 Trademarks: Soyo is the registered trademark of Soyo Computer Inc. Product Rights: All names of the product and corporate mentioned in this publication are used for identification purposes only. The registered trademarks and copyrights belong to their respective companies. No part of this manual may be reproduced, transmitted, transcribed, translated into any other language, or stored in a retrieval system, in any form or by any means, such as by electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without permission in writing from Soyo Computer Inc. [. . . ] The BIOS Setup screen appears: ROM PCI/ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE, INC. SOYO COMBO SETUP STANDARD CMOS SETUP BIOS FEATURES SETUP CHIPSET FEATURES SETUP POWER MANAGEMENT SETUP PNP/PCI CONFIGURATION LOAD SETUP DEFAULTS Esc : Quit F10 : Save & Exit Setup : Select Item (Shift) F2 : Change Color Time, Date, Hard Disk Type. . . SY-7VBA 133 INTEGRATED PERIPHERALS SUPERVISOR PASSWORD USER PASSWORD IDE HDD AUTO DETECTION SAVE & EXIT SETUP EXIT WITHOUT SAVING 2-3. 7 Quick BIOS Setup This Motherboard does not use any hardware jumpers to set the CPU frequency. Instead, CPU settings are software configurable with the BIOS [SOYO COMBO SETUP]. The [SOYO COMBO SETUP] combines the main parameters that you need to configure, all in one menu, for a quick setup in BIOS. After the hardware installation is complete, turn the power switch on, then press the <DEL> key during the system diagnostic checks to enter the Award BIOS Setup program. Select [STANDARD CMOS SETUP] Set [Date/Time] and [Floppy drive type], then set [Hard Disk Type] to "Auto". 45 BIOS Setup Utility Step 2. Select [LOAD SETUP DEFAULT] SY-7VBA 133 Select the "LOAD SETUP DEFAULT" menu and type "Y" at the prompt to load the BIOS optimal setup. Step 3. Select [SOYO COMBO SETUP] Move the cursor to the [CPU Frequency] field to set the CPU frequency. The following table shows all available [CPU Frequency] settings on your SY-7VBA 133 Motherboard . If you set this field to [Manual], you will be required to fill in the next two consecutive fields: (1) the CPU Host/PCI Clock, and (2) the CPU Ratio. CPU Frequency (MHz) 667MHz (66 x 10. 0) 600MHz (133 x 4. 5) Manual 700MHz (66 x 10. 5) 666MHz (133 x 5. 0) 400MHz (66 x 6. 0) 500MHz (100 x 5. 0) 733MHz (133 x 5. 5) 433MHz (66 x 6. 5) 550MHz (100 x 5. 5) 800MHz (133 x 6. 0) 466MHz (66 x 7. 0) 600MHz (100 x 6. 0) 866MHz (133 x 6. 5) 500MHz (66 x 7. 5) 650MHz (100 x 6. 5) 933MHz (133 x 7. 0) 533MHz (66 x 8. 0) 700MHz (100 x 7. 0) 1000MHz (133 x 7. 5) 566MHz (66 x 8. 5) 750MHz (100 x 7. 5) 1. 13GHz (133 x 8. 5) 600MHz (66 x 9. 0) 800MHz (100 x 8. 0) 633MHz (66 x 9. 5) 850MHz (100 x 8. 5) Select the working frequency of your Pentium® III, Celeron processor among these preset values. Note: Mark the checkbox that corresponds to the working frequency of your Pentium® III, Celeron processor in case the CMOS configuration should be lost. Step 4. Select [SAVE & EXIT SETUP] Press <Enter> to save the new configuration to the CMOS memory, and continue with the boot sequence. 46 BIOS Setup Utility SY-7VBA 133 2-3. 8 Troubleshooting at First Start Video (no display) related issues I built a new computer system using a Soyo board and nothing happens when turning it on, no video and no beeps from the PC speaker. No screen and no beeps mean that your CPU and motherboard do not work at all. It could be that the CPU is not seated correctly or that a component on the M/B is grounded (shorted) with the case. Also make sure to check the voltage setting switch (110V/220V) on the back of the power supply. Press and hold down on the "Ins" (insert) key while turning on the Double-check jumpers setting on you motherboard and remove all computer until you get video. If you do not get video then, add-on cards, unplug all hard-disk and floppy-disk drive cables and see if you can hear some beeps. If you still do not get any beeps, then try putting the motherboard on the table (to isolate it from the case) with the CPU and speaker only, and give it one more try. The following lists some basic beep codes and their possible meanings: · One long beep and 3 very short beeps - The video card is not detected by the motherboard. If you are using an AGP card, please push your AGP card down real hard. · Continuous beeps ­ One or more of the memory modules is not seated correctly in its socket. 47 BIOS Setup Utility SY-7VBA 133 My PCI VGA card works fine with my system, but when I put in a new AGP card, it does not give me any video. [. . . ] In order to read a PDF file, the appropriate Acrobat Reader software must be installed in your system. Note: The Start Up program automatically detects if the Acrobat Reader utility is already present in your system, and otherwise prompts you on whether or not you want to install it. You must install the Acrobat Reader utility to be able to read the user's manual file. Follow the instructions on your screen during installation, then once the installation is completed, restart your system and re-run the SOYO CD. 86 Drivers Installation Step 2. [. . . ]