User manual SOYO SY-6KL QUICK START GUIDE

[. . . ] makes no representations or warranties regarding the contents of this manual. We reserve the right to revise the manual or make changes in the specifications of the product described within it at any time without notice and without obligation to notify any person of such revision or change. The information contained in this manual is provided for general use by our customers. Our customers should be aware that the personal computer field is the subject of many patents. [. . . ] Install the CPU Follow the steps below in order to perform the installation of your new SY-6KL Mainboard. Mark your CPU Frequency: Record the working frequency of your CPU that should be clearly marked on the CPU cover. 233MHz (66 x 3. 5) 266MHz (66 x 4. 0) 300MHz (66 x 4. 5) 333MHz (66 x 5. 0) 366MHz (66 x 5. 5) purchased separately, follow these instructions. 1 Unpack the Retention Kit Supporting Base CPU Mount Procedure: To mount the Pentium® II processor that you have 2 Position the Mainboard Slot 1 3 4 Insert the Screws Install the Supporting Base Hardware Installation Support Clip Latches (x2) ATX Power Screws (x2) Heat Sink Retention Clip Larger Pinhole 5 Install the Retention Clip 6 Install the CPU 7 Install the Support Clip 8 Insert the Latches 9 Remember to connect the CPU Cooling Fan to the FAN1 power connector on the mainboard. 6 SY-6KL Quick Start Guide Step 2. Make Connections to the Mainboard This section tells how to connect internal peripherals and power supply to the mainboard. Internal peripherals include IDE devices (HDD, CD-ROM), Floppy Disk Drive, Chassis Fan, Front Panel Devices (Turbo LED, Internal Speaker, Reset Button, IDE LED, and KeyLock Switch. ), Wake-On-LAN card, VGA card, Sound Card, and other devices. For more details on how to connect internal and external peripherals to your new SY-6KL Mainboard, please refer to SY-6KL Mainboard User's Guide and Technical Reference online manual on CD-ROM. Connectors and Plug-ins Connect the SB-Link TM (PC-PCI) cable from your PCI audio card to this header. CPU Cooling Fan: FAN 1 Connect the WOL cable from your LAN card to JP44. Chassis Fan: FAN 3 Connect the CPU cooling fan cable to the Connect the case cooling fan cable to the FAN1 power connector. USB TB LED SPK Plug your USB devices Connect your Turbo LED Connect the speaker cable to to this header. RESET IDE LED KB-LOCK Connect the Power LED and the KB Lock switch to this header. AT Power Supply Connect the AT Power Supply cable to this connector ATX Power Supply: ATX PW Attach the ATX Power cable to this connector. When using the PS/2 Keyboard Wake-Up function, please make sure the ATX power supply can take at least 720mA load on the 5V Standby lead (5VSB) to meet the standard ATX specifications. IrDA (Infrared Device Header): IR1 Connect the cable from your IrDA device to this header. ATX Power On/Off: PWRBT Connect your power switch to this header (momentary switch type). Depending on the BIOS setting, turning off the system is done by "one touch" or by pressing the switch for >4s longer than 4s. ATX Power Select: JPW1 If you use a non-standard ATX power supply, open this jumper. 7 Hardware Installation PCI Audio Card Header: SB-Link TM (PC-PCI) Wake-On-LAN Header: JP44 SY-6KL Quick Start Guide Step 3. Configure Memory Your board comes with three DIMM sockets and two SIMM banks, providing support for up to 384MB of main memory using DIMM modules from 8MB to 128MB and SIMM modules from 8MB to 64MB with no restriction on memory configuration. For 66MHz front side bus CPUs use 12ns or faster memory. Memory Configuration MEMORY CONFIGURATION RAM Type Single RAM Module Size (MB) SIMM Bank Bank 0 EDO 8/16/32/64 DIMM 1 EDO/SDRAM DIMM Banks DIMM 2 EDO/SDRAM DIMM 3 EDO/SDRAM 8/16/32/64/128 8/16/32/64/128 8/16/32/64/128 Hardware Installation Notice 1: You must always install two (2) SIMM modules to complete the SIMM bank. Notice 2: Do not install memory modules in SIMM and DIMM 3 at the same time. Step 4. Set the CPU Frequency You do not need to set any jumper for the CPU frequency. Instead, CPU setting are changed through the BIOS [CHIPSET FEATURES SETUP]. Please refer to Chapter 3 - Quick BIOS Setup for details on how to set the Pentium® II processor frequency. Step 5. Enable/Disable PS/2 Keyboard Wake-Up (JP12) You can choose to enable the Wake-Up by PS/2 Keyboard or Mouse function by shorting pin 1-2 on jumper JP12, otherwise, remove the jumper cap to open pin 1-2 and disable this function. Support Wake-Up by Keyboard JP12 Setting Enable Enable Wake-up by Keyboard or Mouse function (short pin 1-2) Disable* (*Default) Disable Wake-up by Keyboard or Mouse function (open pin 1-2) Important: When using the PS/2 Keyboard Wake-Up function, please make sure the ATX power supply can take at least 720mA load on the 5V Standby lead (5VSB) to meet the standard ATX specifications. 8 SY-6KL Quick Start Guide Step 6. [. . . ] For your convenience, this information is available in HTML format, similar to the format widely used on the Internet. 13 The SOYO CD Note: Once you have selected a driver, the system will automatically exit the SOYO CD to begin the driver installation program. When the installation is complete, most drivers require to restart your system before they can become active. SY-6KL Quick Start Guide (SOYO CD HTML Database in English*) (* The list of menu options may vary between languages) Note: If no HTML browser is installed on your system, the Start Up program will prompt you on whether or not you would like to install the Internet Explorer* browser. Then re-run the SOYO CD and you will be able to browse the SOYO HTML database. (* Internet Explorer is a Microsoft Trademark) The SOYO CD 14 Edition: August 1998 Version 1. 0 6KL SERIAL International Headquarters Soyo Computer Inc. , (Taiwan) Tel: 886-2-2290-3300 Fax: 886-2-2298-3322 Web Site: http://www. soyo. com. tw E-mail: info@mail. soyo. com. tw USA Branch Office Soyo Tek Inc. , (USA) Tel: (408) 452-7696 Fax: (408) 573-7696 Web Site: http://www. soyousa. com E-mail: sales@soyousa. com SOYO Europe Soyo Europe B. V. , (Holland) Tel: 31-79-3637500 Fax: 31-79-3637575 Web Site: http://www. soyo-europe. com http://www. soyo. nl E-mail: Sales@soyo. nl Germany Branch Office SAAT Technology GmbH, (Germany) Tel: 49-(0)444-204044 Fax: 49-(0)441-203422 Web Sites:http://www. saat. de http://www. soyo-saat. de http://www. soyo-saat. com Email: sales@saat. de UK Branch Office Soyo (U. K. ) Ltd. [. . . ]