User manual SOUNDCRAFT RM105 V2

[. . . ] Soundcraft shall not be liable for any loss or damage whatsoever arising from the use of information or any error contained in this manual, or through any mis-operation or fault in hardware contained in the product. No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, electrical, mechanical, optical, chemical, including photocopying and recording, for any purpose without the express written permission of Soundcraft. It is recommended that all maintenance and service on the product should be carried out by Soundcraft or its authorised agents. Soundcraft cannot accept any liability whatsoever for any loss or damage caused by service, maintenance or repair by unauthorised personnel. Harman International Industries Ltd. [. . . ] 4 Pressing T/B routes the signal from the Talkback Bus directly to the Guest Headphones, replacing the PGM signal. (The Talkback Bus normally carries the Presenter's Mic signal via a dedicated Mic/Line input with the Talback jumper fitted). Control Room Monitor 5 Three SOURCE SELECT switches provide a choice of External Input 1, PGM or AUD as the source for the monitors. 3 The LEVEL control sets the output level to the stereo C/Room Monitor jack on the rear panel. The outputs are unbalanced. Master Module 4. 15 2 3 4 1 5 12 7 6 8 9 10 11 RM105 4. 16 Master Module 7 The Control Room Monitors may be muted automatically when local microphones are turned ON and the corresponding Faders opened. The MUTE LED illuminates to show that a 'Mic Live' condition has muted the monitors. The same signal is used to activate a relay which provides two isolated single-pole contact closures on the 9-pin `D'-type REMOTE socket on the rear panel. 8 Normally the Cue signal appears on the Presenter's Heaphones and Cue Speaker in the meterbridge (when fitted). Pressing AUTO CUE routes an active CUE to the Control Room Monitors, replacing the previous source. When the CUE is switched off the monitor returns to the original source. Presenter's Headphones 9 Six SOURCE SELECT switches provide a choice of External Inputs 1-4, PGM or AUD as the source for the headphones. 10 The LEVEL control sets the level of the headphone signal. The METER SELECT switches provide a choice of PGM, AUD or MON (C/Room Monitor) as the source for the meters. Note that the MON position provides a means of monitoring the external inputs via the C/Room Monitor source selection. On the larger frame sizes an additional pair of meters may be fitted, and in this case one pair of meters will always display the PGM output. Power Input The 5way locking POWER connector is the power input to the console. End Users who are consumers should note their rights under this Warranty are in addition to and do not affect any other rights to which they may be entitled against the seller of the Equipment. 3 4 6. 7. A. 4 Appendices CPS150 Power Supply CPS150 Power Supply 43 CPS150 User & Technical Manual IMPORTANT: PLEASE READ THIS MANUAL CAREFULLY BEFORE CONNECTING YOUR SOUNDCRAFT CPS150 POWER SUPPLY TO THE MAINS FOR THE FIRST TIME. WARNING SYMBOLS For your own safety and to avoid invalidation of the warranty all text marked as this paragraph should be read carefully. FOR UK USERS ONLY IMPORTANT WARNING THIS APPLIANCE MUST BE EARTHED The wires in the mains lead are coloured in accordance with the following code: Green and Yellow: Blue: Brown: Earth Neutral Live As the colours of the wires in the mains lead may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: · · · The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol. The wire which is coloured Blue must be connected to the terminal in the plug which is marked with the letter N or coloured Black. The wire which is coloured Brown must be connected to the terminal in the plug which is marked with the letter L or coloured Red. CPS 150 P. 1 Introducing the CPS150 The CPS150 is a linear power supply which, like other linear supplies, produces DC voltages by rectifying, smoothing and regulating AC voltages from the secondary windings of a mains transformer. In regulating these voltages there is some heat generated, the dissipation of which is achieved through a ventilated cover. The CPS150 is designed to be free standing or it can be installed in a 19" rack. For rack mounting, an optional front panel provided with the necessary fixing holes can be obtained from Soundcraft (Part No. Refer to the section "RECOMMENDATIONS FOR INSTALLATION" for details. LED indication is provided on the front panel to show indication of operation of all regulating circuits. SAFETY APPROVAL: HD 195 S6 TYPE TESTED This manual covers the CPS 150 unit, that has been type tested and conforms to the CENELEC Harmonised Document HD195 S6, consisting of IEC 65 (1985)ed 5 and BS 415 1990, with CENELEC deviations. EMC CONDUCTED EMISSION Certification of Conformity has been received for both: USA Statutory Emission Requirements (FCC CFR47 Part 15J, A and B) German Statutory Emission Requirements (VDE0871, A and B) P. 2 CPS 150 Mains Voltage Selection Special attention should be given to the following information: This unit is capable of operating over a wide range of mains voltages by means of a comprehensive set of selectable voltage settings. It is important to ensure that the correct voltage setting has been selected for the level of local mains voltage supply, for safe, uninterrupted operation of the unit. A COVER PLATE is secured to the back panel over the VOLTAGE SELECTION switches. [. . . ] The fuses are held in open fuseholders on the board, close to the other components associated with that circuit. The regulators that are in metal T03 packages can be removed by unscrewing the two M3 screws on each end and lifting them by hand. CPS 150 P. 11 If the electrically insulating SIL pad between the regulator and the heatsink bracket looks damaged then it should be replaced before installing the new regulator. Note that the regulators rely on good thermal contact with the heatsinks to dissipate heat. The regulator fixing screws are used for an electrical connection between the regulator output and the rest of the circuit on the PCB: the case of the T03 package is at the output potential of the device. [. . . ]