User manual SOUNDCRAFT MPMI

[. . . ] USER GUIDE ® USER GUIDE 1 IMPORTANT Please read this manual carefully before using your mixer for the first time. This equipment complies with the EMC Directive 2004/108/EC and LVD 2006/95/EC soundcraft@harman. com © Harman International Industries Ltd. 2010 All rights reserved Parts of the design of this product may be protected by worldwide patents. BD10. 531000 Soundcraft is a trading division of Harman International Industries Ltd. Information in this manual is subject to change without notice and does not represent a commitment on the part of the vendor. [. . . ] Unity gain is provided by the control in the centre-detented position. 7 MUTE All outputs from the channel are enabled when the MUTE switch is released and muted when the switch is down. 8 FADER The 60mm FADER gives you smooth control of the overall signal level in the channel strip, allowing precise balancing of the various source signals being mixed to the Master Section. It is important that the input level is set correctly to give maximum travel on the fader which should normally be used at around the "0" mark. See the "Initial Setup" section on page 33 for help in setting the right level. 9 PFL When the latching PFL switch is pressed, the pre-fade pre-mute signal is fed in mono to the headphones, control room output and meters, where it replaces the MIX. The SOLO LED on the Master section illuminates to warn that a PFL is active. This is a useful way of listening to any required input signal without interrupting the main mix, for making adjustments or tracing problems. 10 CHANNEL PEAK LED This LED will light when the signal level approaches clipping at any of the two monitored points: POST-EQ and POST-FADE. 12 MIX/SUB When this switch is up, the channel's post-fade signal is routed to the Mix (left and right) buses. When the switch is depressed, the post-fade signal is routed to the Subgroup (left and right) buses. 26 Soundcraft MFXi MPMi User Guide 0410 Soundcraft MFXi MPMi User Guide 0410 27 MASTER SECTION (MFXi) L 28 19 9 24 MUTE FX L L REC OUT MONO OUT 48V PHANTOM POWER 2 20 17 MONITOR OUT SUB OUT R L MIX-L R R AUX1 OUT AUX2 OUT FX BUS OUT 2TRK IN 3 MIX-R HEADPHONES R 2TRK LEVEL 18 27 29 30 L [MONO] 4 11 5 7 10 0 10 R TO MIX TO MNTR LEVEL LEVEL STEREO RETURN 0 0 10 10 21 AUX1 MST 0 10 AFL 22 AUX2 MST 0 10 AFL POST PRE FX MST 23 10 0 25 26 12 AFL MNTR LEVEL MIX / SOLO 16 10 0 10 8 6 16 15 MIX SUB STE MNO SUB TO MIX 6 3 0 -3 -6 -12 -16 -22 MF X SOLO PWR 1 10 10 5 5 14 0 0 13 -5 -10 -5 -10 -20 -30 -20 -30 SUB-L SUB-R MIX 28 Soundcraft MFXi MPMi User Guide 0410 MASTER SECTION (MPMi) 18 L 48V PHANTOM POWER 19 9 24 2 20 17 3 4 11 5 7 10 L L REC OUT MONO OUT MONITOR OUT SUB OUT R L MIX-L R R AUX1 OUT AUX2 OUT AUX3 OUT 2TRK IN R 2TRK LEVEL MIX-R HEADPHONES 0 10 TO MIX TO MNTR LEVEL 0 10 AUX1 MST 0 10 AFL AUX2 MST 0 10 21 23 22 AUX3 MST AFL POST PRE 0 10 AFL MNTR LEVEL MIX / SOLO 16 10 0 10 8 6 16 15 MIX SUB STE MNO SUB TO MIX 6 3 0 -3 -6 -12 -16 -22 12 MPM SOLO PWR 1 10 10 5 5 14 0 0 13 -5 -10 -5 -10 -20 -30 -20 -30 SUB-L SUB-R MIX Soundcraft MFXi MPMi User Guide 0410 29 1 POWER INDICATOR This LED lights to show when power is connected to the console. 2 PHANTOM POWER Many professional condenser mics need PHANTOM POWER, which is a method of sending a powering voltage down the same wires as the mic signal. WARNING: TAKE CARE when using unbalanced mics which may be damaged by the phantom power voltage. Balanced dynamic mics can normally be used with phantom power switched on (contact your microphone manufacturer for guidance). Mics should always be plugged in, and all output faders set to minimum before switching the Phantom Power ON to avoid damage to external equipment. 2-TRACK 3 2-TRACK IN These two RCA phono sockets are unbalanced Left and Right line-level inputs, used for connecting a playback device. 4 2-TRACK LEVEL CONTROL This adjusts the signal level from the 2-Track inputs. 5 2-TRACK TO MIX Press this switch to route the 2-Track input signals to the MIX Left/Right bus. The level is set with the 2-Track level control. MONITOR SOURCE The following two switches select the signal source(s) to be monitored. 7 2-TRACK Press this switch to monitor the 2-Track input signal. MONITOR OUT 8 MONITOR OUTPUT LEVEL This control sets the signal level fed to the MONITOR LEFT & RIGHT outputs. 9 MONITOR OUTPUTS The Monitor Outputs are on 3-pole 6. 35mm (1/4") jacks and are balanced. 10 HEADPHONES LEVEL This control sets the level of the Headphone output. 11 HEADPHONES SOCKET The PHONES output is a 3-pole 6. 35mm (1/4") jack, wired as a stereo output, ideally for headphones of 32 or greater. [. . . ] Insert A break point in the signal path to allow the connection of external devices, for instance signal processors or other mixers at line level signals. Nominal levels can be anywhere between 0dBu to +6dBu, usually coming from a low impedance source. Pan (pot) Abbreviation of `panorama': controls the levels sent to left and right outputs. Peaking The point at which a signal rises to its maximum instantaneous level, before falling back down again. [. . . ]