User manual SOUNDCRAFT DC 2020

[. . . ] 1995 All rights reserved Parts of the design of this product are protected by worldwide patents. Part No. ZM0103-01 Information in this manual is subject to change without notice and does not represent a commitment on the part of the vendor. shall not be liable for any loss or damage whatsoever arising from the use of information or any error contained in this manual, or through any mis-operation or fault in hardware or software contained in the product. No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, electrical, mechanical, optical, chemical, including photocopying and recording, for any purpose without the express written permission of Soundcraft Electronics Ltd. [. . . ] Pressing this will copy into the existing list all the timecodes from the cue list. Playback must be ON to enable MIDI codes to be transmitted against timecode. This inserts a new NO EVENT command with the currently-displayed timecode. This allows you to edit the Event Name (even if Event Type is currently being displayed). The default name given to all Midi Events is MIDI EVENT X DC2020 The Automation Pages 4. 73 where X is the next available number. Note that the numbers are not in timecode order: they are in the order that the Midi Events were inserted into the list. This allows you to edit the timecode value of the Midi Event which is displayed in the Cursor Line. Note that if the event type for a particular event is blank, the event is a NO TYPE event. 4. 74 DC2020 The Automation Pages Mix The Mix page appears as follows: Mix: New Mix Pass Title: Song 1 Project: PROJECT 0001 Percentage free: 95% User: DC2000 User 0001 00 Program start Used Cue Point Used Cue Point Title Config Edit Cue Name Project Edit Timecode Mix List Delete Cue 01:09:55:00 01:09:57:00 01:09:58:00 New Mix Title Utilities The following information is presented: Screen Title Area The Mix name. Note that the Pass Number is shown at the top right of the screen. Subsidiary Data Area The Title name, the Percentage of disk space which is free, the Project name and the User name. Scrollable Data The list of Cue Points for the Mix are displayed. If you touch the Cursor Line, the tape machine will transport to the appropriate Cue (providing that the tape machine supports this function). The four cue points, LOCATE0, LOCATE1, DROP IN and DROP OUT, are shown against their assigned cues as L0, L1, D1 and DO. Touch-pads Title Config. This prepares a new Mix number with no recorded actions, and drops all automated functions into write mode, ready to start a new Mix. The previous Mix is, of course, saved on disk and you may come back to it at a later stage. This, not surprisingly, allows you to edit the Cue name. DC2020 The Automation Pages 4. 75 Edit Timecode. This allows you to enter new time information into the Cue which is on the Cursor Line. You may also use the Jog Wheel to change the time information frame-by-frame. Pressing this takes you to the Title Utilities page. 4. 76 DC2020 The Automation Pages Mix Information The Mix Information page appears as follows: The following information is presented: Screen Title Area Title only. Scrollable Data The following fields are available within the scrollable area. Each of them may be positioned within the Cursor Line, and selected by touching the Cursor Line. The data which you enter here is stored for information only: it has no meaning to the Automation system. Touching this field whilst it is in the Cursor Line takes you to the Alphanumeric Keypad page. Touching this field whilst it is in the Cursor Line takes you to the Alphanumeric Keypad page. Touching this field whilst it is in the Cursor Line takes you to the Alphanumeric Keypad page. [. . . ] Don't forget to connect timecode output from the tape to CODE IN. )RVWH[*6HULHV TIME CODE TRACK OUT TIME CODE IN MIDI IN MIDI OUT MIDI OUT MIDI IN DC2020 Appendix A A. 9 Fostex R series (MIDI) Additional Hardware Required Fostex MTC-1 Interface (Software version greater than 1. 3 required for full functionality) Transport Controls All supported, machine sends back tallies Locate To Timecode Supported. Record Enable/Rehearse Supported. Possible problem with old Fostex exclusive messages on machines earlier than rom revision 1. 4. Jog/Shuttle Not supported by Fostex R series machines. Setup Notes Remember to connect Timecode from tape track to MTC1. Set dipswitch on back to all zeros except switches 8 & 6. )RVWH[56HULHV TIME CODE TRACK OUT TIME CODE IN MIDI IN MIDI OUT MIDI OUT MIDI IN A. 10 DC2020 Appendix A Fostex RD-8 (LTC)(Midi Machine Control ) Transport Controls All Supported, Tallies generated by LTC. Locate to Timecode Supported Record Enable/Rehearse This function is supported, but automatic drop-ins are not supported by the Fostex RD-8 using MMC. [. . . ]