User manual SONY XDR-S55DAB

[. . . ] · To set the current time exactly to the seconds, adjust the minute function in step 4 and then press PRESET/ENTER to synchronize it with a time signal (such as the telephone time signal). For example, in the 24-hour system, "0:00" is indicated as midnight, and "12:00" is indicated as noon. Notes · If you do not operate within 65 seconds while setting the clock, the clock setting mode will be cancelled. (See "Changing the display"). XDR-S55DAB © 2007 Sony Corporation Printed in China Choosing power sources Installing Batteries (See fig. [. . . ] The aerial can be damaged when you move the aerial with excessive force. About the SC (Secondary Component) If the selected primary component has a secondary component, "SC " blinks on the display. BETA 4 EUROPEAN EQUITIE Press ·DAB/FM SC for more than 2 seconds to receive the desired secondary component. Turn U/u or pressing ·DAB/FM SC does the following: U (up) or u (down) DC IN 6V Initial setting for the DAB When the batteries are installed, or when the AC power adaptor is plugged in for the first time after purchase (or after resetting), the unit will automatically scan and create a list of receivable broadcasts. If you wish to scan for the DAB broadcasts again, or when the unit is reset, do the following: Ensemble Service 1 Component Service 2 Component Service 3 Component Secondary Component DAB / FM SC D Aerial 1 2 3 4 Adjust the aerial accordingly. Hold down AUTO TUNE for more than 2 seconds. "INIT INITIALIZE OK?" appears in the display. Press PRESET/ENTER. No sound will be heard, and "<SCANNING>" appears in the display. When finished, the unit receives the first service in alphabetical order stored by the DAB scan. Service 4 Component Secondary Component A Secondary Component B INIT <SCANNING> Note When the selected secondary component is finished, the unit returns automatically to the primary component. E Notes · If you do not operate within 65 seconds, the initial scan mode will be cancelled. · If no broadcasts are found by the DAB scan, "SIGNAL NOT FOUND" appears in the display. SIGNAL NOT FOUND · To cancel the DAB scan halfway, press AUTO TUNE. Any services received before you cancel are added to the list of receivable services. · If the batteries are removed for a certain period, the received history list will be deleted, requiring you to scan again. · If you set the initial setting, any DAB services registered as PRESET are erased. · If you change the unit's location of use, or want to add a new service after the initial setting, press and release AUTO TUNE. "FULL <SCANNING>" appears in the display and the unit will automatically scan and create a list of receivable services. RESET button Continue to next page Presetting your favourite services or stations There are two ways to preset services, Direct Preset and Preset Mode. You can preset 10 services in DAB and 10 stations in FM, including 3 services stored on the Direct Preset buttons (PRESET 1 ­ 3). You can enjoy any three preset services as Direct Presets, for immediate recall by pressing one of the PRESET 1 ­ 3 buttons. Preset services you use often to Direct Preset for your convenience. Scan tuning (FM only) The unit will automatically scan FM station. Precautions · Operate the unit only on the power sources specified in "Specifications". · The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off. · Use the unit within a temperature range of 0°C to 40°C (32°F to 104°F). If it is used in temperatures higher than this range, numbers may appear in the display which have nothing to do with the frequency being received. If it is used in temperatures lower than this range, the numbers displayed may change very slowly. (These irregularities will disappear and there will be no damage to the unit when the unit is used in the recommended temperature range. ) · The nameplate indicating operating voltage, etc. · Avoid exposure to temperature extremes, direct sunlight, moisture, sand, dust or mechanical shock. [. . . ] The sound through the speaker will not be heard. To illuminate the LCD Press LIGHT to select the backlight on or off. Notes · The first time you turn on the unit in AC operation, the backlight is set to on (default). · When DC operation, the backlight will turn off automatically if no operation is performed for 30 seconds. Stretched display Hold down the DISPLAY for more than 2 seconds (receiving the DAB service, the component label should be displayed in the first line), the first line in the display changes to stretched display. Preventing Accidental Operation -- HOLD Function This function prevents the radio from being unintentionally turned on, or the radio service frequency from being accidentally changed. When any key is pressed, "<HOLD>" blinks for 3 seconds and all buttons on the radio become inoperative. [. . . ]