User manual SONY VAIO VPCB11LGX/B

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SONY VAIO VPCB11LGX/B. We hope that this SONY VAIO VPCB11LGX/B user guide will be useful to you.


SONY VAIO VPCB11LGX/B : Download the complete user guide (2662 Ko)

You may also download the following manuals related to this product:

   SONY VAIO VPCB11LGX/B QUICK START GUIDE (1171 ko)
   SONY VAIO VPCB11LGX/B DATASHEET (880 ko)
   SONY VAIO VPCB11LGX/B QUICK START GUIDE (1171 ko)
   SONY VAIO VPCB11LGX/B HARD DISK DRIVE REPLACEMENT INSTRUCTIONS (384 ko)
   SONY VAIO VPCB11LGX/B OPTICAL DISK DRIVE REPLACEMENT INSTRUCTIONS (348 ko)

Manual abstract: user guide SONY VAIO VPCB11LGX/B

Detailed instructions for use are in the User's Guide.

[. . . ] PCMCIA is a trademark of the Personal Computer Memory Card International Association. Intel and Pentium are registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Netscape 7. 0 is a registered trademark of Netscape Communications Corporation. PowerQuest and Drive Image are registered trademarks of PowerQuest Corporation. [. . . ] Check your power management settings, or close your applications and go to the Power Savings menu of the setup utility to adjust the timeout values to better suit your operation needs. (See BIOS Setup Utility on page 29 for more information) Press any button on the keyboard, or move the mouse to restore operation. (The display may be shut off by Standby Mode, Auto Suspend or Video Timeout) Check the Closed Cover switch. (See figure 2-4 on page 6 for location) Check the status indicator panel to verify that the Security icon is blinking. Remove all foreign objects from the keyboard. The power management timeouts may be set for very short intervals and you failed to notice the display come on and go off again. Your system display won't turn on when the system is turned on or when the system has resumed. The system may be passwordprotected. A foreign object, such as a paper clip, is stuck between the display and the keyboard. If the spots are very tiny and few in number, this is normal for a large LCD display. If the spots are numerous or large enough to interfere with your operation needs. This is normal; do nothing. Display is faulty; contact your support representative. 62 S Series. book Page 63 Monday, September 15, 2003 4:48 PM Tro ublesho oting Problem Possible Cause Possible Solutions The application display uses only a portion of your screen and is surrounded by a dark frame. You are running an application that does not support 800 x 600/1024 x 768 pixel resolution display and display compression is enabled. Display compression gives a clearer but smaller display for applications that do not support 800 x 600/1024 x 768 pixel resolution. You can fill the screen but have less resolution by changing your display compression setting, (See the Video Features submenu, located within the Advanced menu of the BIOS. (See BIOS Setup Utility on page 29 for more information) Press [Fn] + [F7] to increase brightness or doubleclick on the battery gauge and adjust Power Control under battery settings. This is a serious fault that may cause you to lose data if you continue. *Fixed Disk x Failure or Fixed Disk Controller Failure (where x = 1-4) The fixed disk is not working or not configured properly. This may mean that the hard drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to check for the hard drive type settings and correct them if necessary. If the settings are OK and the message appears when you restart the system, there may be a serious fault which might cause you to lose data if you continue. Contact your support representative. *Incorrect Drive A type ­ run SETUP Type of floppy drive A: not correctly identified in Setup. This means that the floppy disk drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. *Incorrect Drive B type ­ run SETUP Type of floppy drive B: not correctly identified in Setup. This means that the floppy disk drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. In the unlikely case that you see this message you may have some display problems. You can continue operating but should contact your support representative for more information. [. . . ] The personal computer uses the same network key both for data encryption and decryption, therefore, it is necessary to set the same network key as the other side of communication. Network name (SSID: Security Set Identifier) When a wireless LAN network is configured, grouping is performed to avoid interference or data theft. In order to improve security, the network key is set allowing no communication unless "Network name (SSID)" coincides with the network key. Open system authentication One of network authentication types for wireless LAN. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SONY VAIO VPCB11LGX/B




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SONY VAIO VPCB11LGX/B will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.