User manual SONY PCK-LM13 DATASHEET

[. . . ] 3-1 Paper Guide iv Table of Contents Xerox Nuvera Stock types . 4-1 4-1 4-2 4-2 4-2 4-2 4-2 A Converting paper weight from pounds to gsm . B-1 B-2 B-2 B-3 B-4 B-4 B-4 C-1 C-1 C-2 C-2 C-3 C-3 C-3 C-4 C Managing the Feeder . . F-1 v Paper Guide Introduction This guide provides information for selecting, storing, and using paper in the Xerox Nuvera family of products. [. . . ] · Most drilled papers with common hole patterns will run reliably. Common hole patterns include, 3-hole standard, 7-hole, European din 4-hole, Swedish 4-hole, Norwegian 6-hole. Some hole configurations, especially holes that are close to the edge of the sheet, will cause frequent jams. Sheets should not stick together at the holes (hole welding caused by a dull drill). Paper plugs should not be present in the holes. Selection tips · · · Storage tips Usage tips Follow general guidelines in Chapter 2. · Load drilled paper with the holes on the lead edge (left side) of the paper tray. Paper handling will be best when holes are loaded at the trail edge. Note When feeding tab stock and drilled stock in the same job, the drilled stock must be loaded with the holes on the leading edge, not the trail edge, so that the stock orientation is the same as for the tab stock. · Load reinforced paper with the plastic strip facing down. Envelopes Description Selection tips Envelopes are specialty stocks that have a flap for mailing documents. · · Storage tips Usage tips Booklet Envelopes: Use only 6"x9", 9"x12", C5 (162x229mm), or 220x312mm sized envelopes Catalog Envelopes: Use only 6"x9", 7"x10", C5 (162x229mm), or 178x254mm sized envelopes Follow general guidelines in Chapter 2, Managing your paper supply. · · · · Booklet Envelopes should be loaded with the flap closed, flap down, and on the leading edge Catalog Envelopes should be loaded with the flap open, flap down, and on the outboard edge Only load 50 envelopes at a time to keep the stack as level as possible Do not use envelopes with latex-based glue closures (for example, self-sealing envelopes Paper Guide 3-5 Tips by stock type Xerox Nuvera Heavyweight Coated (140 to 220 gsm) Description Selection tips Storage tips Usage tips Any coated paper for use in printing that weighs 140 gsm or more. Coatings may be applied to one or both sides to enhance image quality. Perforations should be created so sheets will maintain as much stiffness as possible. Perforations should be strong enough to not tear during the printing process. Selection tips Follow general guidelines in Chapter 2. · · To prevent contaminating the printer, use only mechanically perforated papers that are free of paper dust and chaff. Where possible, load with the perforation parallel to the feed direction. 3-8 Paper Guide Xerox Nuvera Tips by stock type · CAUTION Never print on sheets that were printed with rubber-based inks or cured with a drying agent (starch, talc, or rosin powders). Machine contamination will result, causing background spotting, streaking, deposits in the fuser and/or spots on the photoreceptor. If you wish to use a preprinted paper that has not been tested by Xerox, check with your Xerox representative first. Preprinted Paper Note When printing over offset inks, image permanence may be compromised. Description Any previously printed paper that will be printed on again. Examples of preprinted papers are forms, mailers and catalogs that will be personalized with customer names and addresses. · Select papers printed with laser-compatible, lithographic inks to minimize offsetting. UV-cured inks are recommended, especially on coated stocks, to insure complete drying before printing on a Xerox Nuvera. Design the preprinted image so that no ink, varnish, or aqueous coating is placed in the area to be printed on by a Xerox Nuvera. [. . . ] Porosity depends on the number of pores in a sheet as well as the size, shape and distribution of pores. Paper and packaging that have been printed on, used at least once by consumers, and then submitted for recycling. An integrated workstation, running Xerox software, for interfacing with and managing the Xerox Nuvera. A jam caused by a sheet of paper becoming wrapped around the pressure roll in the fuser. [. . . ]