User manual SONY ICD-P17

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SONY ICD-P17. We hope that this SONY ICD-P17 user guide will be useful to you.


SONY ICD-P17 : Download the complete user guide (568 Ko)

You may also download the following manuals related to this product:

   SONY ICD-P17 (674 ko)
   SONY ICD-P17 (513 ko)
   SONY ICD-P17 (674 ko)
   SONY ICD-P17 (683 ko)
   SONY ICD-P17 (686 ko)
   SONY ICD-P17 (687 ko)
   SONY ICD-P17 (676 ko)
   SONY ICD-P17 (682 ko)
   SONY ICD-P17 (670 ko)
   SONY ICD-P17 annexe 1 (679 ko)
   SONY ICD-P17 annexe 1 (679 ko)
   SONY ICD-P17 (569 ko)
   SONY ICD-P17 (674 ko)
   SONY ICD-P17 annexe 1 (569 ko)
   SONY ICD-P17 annexe 2 (569 ko)
   SONY ICD-P17 ADDENDUM (19 ko)
   SONY ICD-P17 DATASHEET (187 ko)
   SONY ICD-P17 SUPPLIED ACCESSORIES ADDENDUM (20 ko)

Manual abstract: user guide SONY ICD-P17

Detailed instructions for use are in the User's Guide.

[. . . ] 3-255-789-11 (1) BGetting started BBasic Operations IC Recorder Operating Instructions Owner's Record The model number is located at the rear and the serial number is located inside the battery compartment. Refer to these numbers whenever you call upon your Sony dealer regarding this product. ICD-P17 Serial No. Step 1: Installing the Batteries Recording Messages Replacing the batteries The battery indicator on the display window shows the battery condition. flashes, the batteries are When exhausted and the unit will stop operation. [. . . ] or >+ to select the digits of the hour. The remaining time displayed in the display window is shorter than that displayed in the supplied "Digital Voice Editor" software. · The unit requires a certain amount of memory for system operation. That amount is subtracted from the remaining time, which is the reason for the difference. 2 Press NxPLAY/STOP. The minute digits will flash. 4 Press NxPLAY/STOP at the time signal. The display will return to "SET DATE". The unit does not operate correctly. · Take out the battery and insert it again. Please note that recorded messages may be erased during service or repair work. 5 Press MENU to exit from the menu mode. Backup recommendations To avoid potential risk of data loss caused by accidental operation or malfunction of the IC recorder, we recommend that you save a backup copy of your recorded messages on a tape recorder or to a computer, etc. The display is shown at all times. Erasing Messages You can erase the recorded messages one by one or all messages in a folder at a time. Note that once a recording has been erased, you cannot retrieve it. BVarious Ways of Recording BOther Functions Adding a Recording Using an Adding Recording At a factory setting, you cannot add a recording not to erase the message by accidental operation. If you want to add a recording to a previously recorded message or add an overwrite recording, change the REC-OP setting in the procedures below. Dividing a Message into Two/ Combining Messages You can divide a message, or combine messages. · You can divide a message into two while recording/ playing back messages. Note Due to the recording system of an IC recorder, you may not be able to divide or combine messages in some cases (see "Troubleshooting"). Moving Messages to a Different Folder -- Move Function You can move the recorded messages to another folder. Example: Moving Message 3 in Folder A to Folder B 4 Press NxPLAY/STOP. The hour digits will flash. Selecting the Display Mode You can select the display mode for the stop, recording and playback modes. (If the unit is left unoperated for more than 3 seconds in the stop mode, the display will show the current time, regardless of the display mode setting. ) Each time you press DISPLAY, the display mode will change as shown below: Playing Back All Messages in a Folder Continuously CONT ON: You can play back all messages in a folder continuously. CONT OFF: Playback stops at the end of each message. 5 Set the alarm time. 1 Press ­ . or >+ to select the minute digits and press NxPLAY/STOP. 1 Play back the message you want to move. 1 Erasing messages one by one When a message is erased, the remaining messages will advance and renumbered so that there will be no space between messages. Before erasing Message 1 Message 2 Message 3 Message 4 Message 5 Press MENU to enter the menu mode. 1 Press MENU to enter the menu mode. , Counter: Elapsed playback/recording time in one message Dividing a Message 2 Erase Message 3 After erasing Message 1 Message 2 Message 3 Message 4 2 Remaining messages are renumbered. Press ­ . or >+ to display "REC-OP" and press NxPLAY/ STOP. The adding recording window will be displayed. To cancel erasing 1 Press ERASE while playing back the message you want to erase or press ERASE for more than 1 second during stop mode. A beep will sound and the message number and "ERASE" will flash while the first and last 5 seconds of the message is played back 10 times. (For example, if you erase Message 3, Message 4 will be renumbered as Message 3. When erasing is completed, the unit will stop at the beginning of the following message. ) Press STOP before step 2. 3 4 To erase other messages Repeat steps 1 and 2. Press ­ . or >+ to select "ON" and press NxPLAY/STOP. The setting is changed. You can divide a message during recording or playback, so that the message is divided into two and the new message number is added to the divided message. By dividing a message, you can easily find the point you want to play back when you make a long recording such as a meeting. [. . . ] 4 Press MENU to exit the menu mode. 3 MIC (built-in microphone) Display window FOLDER DIVIDE DISPLAY MIC SENS (microphone sensitivity) MENU ERASE Speaker STOP Recording with an External Microphone or from Other Equipment Message 1 Message 2 Message 3 Message 4 Messages are combined. Press ­ . or >+ to select "ON" or "OFF" and press NxPLAY/STOP. The setting is completed. Connecting cable (supplied) Message 1 Message 2 Message 3 To USB connector of your computer 1 Connect a plug-in-power type microphone or other equipment to the MIC (PLUG IN POWER) jack. The message numbers decrease. In stop mode, follow the steps below: 3 Set the alarm date. To play back on a desired date (the message will be played back at the same time on the same date every year until you erase the message) 1 Press NxPLAY/STOP while "DATE" is flashing. The year digits will flash. 4 Press MENU to exit the menu mode. When recording with an external microphone mini-plug (monaural) MIC External microphone (not supplied) 1 Press ­ . [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SONY ICD-P17




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SONY ICD-P17 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.