User manual SONY HCD-EC55

[. . . ] 2-899-084-11(1) NOTICE FOR THE CUSTOMERS IN THE U. S. A. CAUTION Mini Hi-Fi Component System Operating Instructions Owner's Record The model and serial numbers are located on the rear of the unit. Refer to them whenever you call upon your Sony dealer regarding this product. ______________ You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems) Basic Operations * Adjusting the sound To adjust the volume Press VOLUME +/­ on the remote (or turn the VOLUME control on the unit) . Notes on playing multisession discs If the disc begins with a CD-DA (or MP3) session, it is recognized as a CD-DA (or MP3) disc, and playback continues until another session is encountered. A disc with a mixed CD format is recognized as a CD-DA (audio) disc. Using optional audio components To connect an optional headphones Connect headphones to the PHONES jack on the unit. To add a sound effect To Generate a more dynamic sound (Dynamic Sound Generator X-tra) Press DSGX on the unit. Listening to the radio 1 Select "FM" or "AM. " Press TUNER/BAND repeatedly. To connect an optional component GB This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] High channel With 8 ohm loads, both channels driven, from 2, 000 ­ 13, 000 Hz; 60 watts per channel minimum RMS power, with no more than 0. 7% total harmonic distortion from 250 milliwatts to rated output. AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: (MHC-EC55 The United States model only) With 6 ohm loads, both channels driven, from 120 ­ 10, 000 Hz; 45 watts per channel minimum RMS power, with no more than 0. 7% total harmonic distortion from 250 milliwatts to rated output. General Powerrequirements: North American model: AC 120 V, 60 Hz European and Russian models: AC 230 V, 50/60 Hz Australian model: AC 230 ­ 240 V, 50/60 Hz Mexican model: AC 127 V, 60 Hz Argentine model: AC 220 V, 50/60 Hz Korean model: AC 220 V, 60 Hz Saudi Arabian model: AC 120 ­ 127, 220 ­ 240 V, 50/60 Hz, adjustable with voltage selector Other models: AC 120, 220 or 230 ­ 240 V, 50/60 Hz, adjustable with voltage selector 2 Press to turn off the system. 3 After "STANDBY" stops flashing, press DISPLAY Notes on discs 2 Find your problem in the checklist below, and take 1 Press CD to select the CD function. 2 Press PLAY MODE repeatedly until "PGM" appears while the player is stopped. 1 Insert a recordable tape into the cassette holder with the side you want to record facing up. the indicated corrective action. If the issue persists, contact your nearest Sony dealer. 3 Press DISC SKIP to select a disc. 4 Press / (or / on the unit) 2 Prepare the recording source. Select the desired source to record. Place the disc you want to record and press DISC SKIP/EX-CHANGE to select a disc. When recording a folder from an MP3 disc, press PLAY MODE repeatedly to select " , " and then press +/­ repeatedly to select the desired folder. To record only your favorite CD tracks or MP3 files in your desired order, perform steps 2 to 5 of "Creating your own CD program. " repeatedly until the desired track number appears. When programing MP3 files, press +/­ repeatedly to select the desired folder, and then select the desired file. Selected track or file number Immediately unplug the power cord, and check the following item. If your system has a voltage selector, is the voltage selector set to the correct voltage?After the STANDBY indicator on the unit stops flashing, reconnect the power cord, and turn on the system. If the issue persists, contact your nearest Sony dealer. If the STANDBY indicator flashes to display the clock and then press while holding down on the unit. To turn on CD player power, repeat the procedure until "CD POWER ON" appears. To reset the system to factory settings Before playing, wipe the disc with a cleaning cloth from the center out to the edge. Do not clean discs with solvents, such as benzine thinner, or commercially available cleaners or antistatic spray intended for vinyl LPs. Do not expose discs to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight. Powerconsumption: MHC-GX99 USA model: 190 W Canadian model: 245 VA USA model: 115 W Canadian model: 155 VA USA model: 190 W Canadian model: 245 VA European and Russian models: 140 W 0. 5 W (in Power Saving Mode) Other models: 150 W USA model: 95 W Canadian model: 130 VA European and Russian models: 95 W 0. 5 W (in Power Saving Mode) Other models: 95 W Approx. 200 × 306 × 410 mm If the system still does not operate properly, reset the system to factory settings. Use buttons on the unit to reset the unit to its factory default settings. On safety 1 Disconnect and reconnect the power cord, and then turn on the system. 2 Press PLAY MODE , FUNCTION , and at General The system does not turn on. Is the power cord plugged in? Is the voltage selector set correctly to match the local power line voltage?Saudi Arabian models also may not turn on when the voltage selector is set to NO OPERATION. 3 Start recording. Total playing time of the selected track the same time. All user-configured settings, such as preset radio stations, timer, and the clock, are deleted. 5 Press ENTER to add the track or file to the program. 6 Repeat steps 3 through 5 to program additional tracks or files, up to a total of 25 tracks or files. Press (record) , and then start playing the desired recording source. If there is noise while recording from the tuner, reposition the appropriate antenna to reduce the noise. [. . . ] Do not use any type of abrasive pad, scouring powder, or solvent, such as thinner, benzine, or alcohol. Inputs AUDIO IN (stereo mini jack): Sensitivity 800 mV, impedance 47 kilohms PHONES (stereo mini jack): Accepts headphones with an impedance of 8 or more SPEAKER: Accepts impedance of 6 to 8 SUBWOOFER OUT (MHC-GX99 only) Outputs Play does not start from the first track. 3 Press +/­ (or TUNING + or ­ on the unit) 2 Press CLOCK/TIMER SET . 3 Press / repeatedly to select "PLAY, " and 4 Set the time to start playing. Press / repeatedly to set the hour, and then press ENTER . Use the procedure above to set the minutes. Return to Normal Play by pressing PLAY MODE repeatedly until both "PGM" and "SHUF" disappear. To prevent a tape from being accidentally recorded over repeatedly to select your desired preset number. If another station is already assigned to the selected preset number, the station is replaced by the new stations. then press ENTER . [. . . ]