User manual SONY CMT-BX20I

[. . . ] When placing or removing the iPod, brace the unit with one hand and take care not to press the controls of the iPod by mistake. To remove the iPod Dock Adaptor, pull it up with your fingernail or a flat object using the slot inside the adaptor. Sony cannot accept responsibility in the event that data recorded to iPod is lost or damaged when using an iPod with this unit. Playing a CD/MP3 disc 1 Select the CD function. Press FUNCTION +/ (or FUNCTION on the unit) repeatedly. To stop automatic scanning © 2008 Sony Corporation This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Press (stop) (or /CANCEL on the unit) . Changing the display To Change information on the display1) Check the clock when the system is off2) 1) To tune in a station with a weak signal 2 Place a disc. Press (open/close) on the unit, and place a disc with the label side up on the disc tray. WARNING To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. To reduce the risk of fire, do not cover the ventilation opening of the apparatus with newspapers, tablecloths, curtains, etc. Do not place the naked flame sources such as lighted candles on the apparatus. [. . . ] If the issue persists, contact your nearest Sony dealer. The sound is distorted. 2 Press PLAY MODE repeatedly until "PGM" appears 3 Press / repeatedly until the desired track or file number appears. When programming files, press +/ repeatedly to select the desired folder, and then select the desired file. Sleep Timer: You can fall asleep to music. If you select "AUTO, " the system automatically turns off after the current disc stops or in 100 minutes. If the STANDBY indicator flashes Turn down the volume. Set the "EQ" setting of the iPod to "Off " or "Flat. " Play Timer: You can wake up to CD, tuner or iPod at a preset time. Make sure you have set the clock. 1 Prepare the sound source. Selected track or file number Total playing time of program (including selected track or file) Prepare the sound source, and then press VOLUME +/ to adjust the volume. To start from a specific track or file, create your own program. Immediately unplug the power cord, and check the following items. If your system has a voltage selector, is the voltage selector set to the correct voltage? Is anything blocking the ventilation holes on the top or back of the system?After the STANDBY indicator stops flashing, reconnect the power cord, and turn on the system. If the issue persists, contact your nearest Sony dealer. The iPod cannot be charged. Make sure the iPod is connected securely. locations that are extremely hot, cold, dusty, dirty, or humid or lacking adequate ventilation, or subject to vibration, direct sunlight or a bright light. Be careful when placing the unit or speakers on surfaces that have been specially treated (for example, with wax, oil, polish) as staining or discoloration of the surface may result. If the system is brought directly from a cold to a warm location or is placed in a very damp room, moisture may condense on the lens inside the CD player, and cause the system to malfunction. In this situation, remove the disc, and leave the system turned on for about an hour until the moisture evaporates. Speaker system: Full-range, bass-reflex, 10 cm, cone type Rated impedance: 6 ohms Dimensions (w/h/d): Approx. 1. 9 kg net Power requirements: North American model: 120 V AC, 60 Hz Australian model: 230 240 V AC, 50/60 Hz Other models: 120 V, 220 V, 230 240 V AC, 50/60 Hz, adjustable with voltage selector Power consumption: 63 watts Dimensions (w/h/d) (excl. 3. 9 kg Supplied accessories: Remote Commander (1)/R6 (Size AA) batteries (2)/AM loop antenna (1)/FM lead antenna (1)/iPod Dock Adaptors (1 set) (Except for Australian model) Design and specifications are subject to change without notice. General Messages CD Over: You have reached the end of the disc while pressing during playback or pause. No Disc: There is no disc in the system, or you have loaded a disc that cannot be played. Step Full!: You tried to program more than 26 tracks or files (steps). TIME NG!: The Play Timer start and end times are set to the same time. On heat buildup Heat buildup on the unit during operation is normal and is not cause for alarm. Do not touch the cabinet if it has been used Standby power consumption: 0. 5 W Halogenated flame retardants are not used in the certain printed wiring boards. (Except for the United States model) continuously at a high volume because the cabinet may have become hot. Do not obstruct the ventilation holes. General Sound comes from one channel, or the left and right volumes are unbalanced. Place the speakers as symmetrically as possible. Connect only the supplied speakers. On the speaker system 4 Press (or ENTER on the unit) to add the track or file to the program. " appears when the total program time exceeds 100 minutes for a CD, or when you select a CD track whose number is 21 or over, or when you select an MP3 file. [. . . ] By default, CD power is turned on. Copyrights 1 Press FUNCTION +/ (or FUNCTION on the unit) repeatedly to select the CD function, and then turn off the system. 2 After "STANDBY" stops flashing, press on the unit while holding down CANCEL on the unit. To turn on CD player power, repeat the procedure until "CD POWER ON" appears. iPod is a trademark of Apple Inc. , registered in the U. S. MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer IIS and Thomson. All other trademarks and registered trademarks are of their respective holders. [. . . ]