User manual SMC SMCFS2601

[. . . ] SMC reserves the right to change specifications at any time without notice. Copyright © 2011 by SMC Networks, Inc. 20 Mason Irvine, CA 92618 All rights reserved Trademarks: SMC is a registered trademark; and EZ Switch, TigerStack and TigerSwitch are trademarks of SMC Networks, Inc. [. . . ] The WRR queue-scheduling algorithm schedules all the queues in turn with every queue assured a certain service time. The default weight values of TC0 and TC1, are 1:16 ­ 12 ­ 2 HARDWARE DESCRIPTION This chapter describes the front panel, rear panel, and LED indicators of the switch. FRONT PANEL The front panel of SMCFS2601 consists of switch LED indicators, 24 10/100 Mbps RJ-45 ports and 2 10/100/1000 Mbps RJ-45 ports. Figure 2: SMCFS2601 Switch Front Panel 1 3 5 7 9 11 13 15 17 19 21 23 GIGA1 Power GIGA1 GIGA2 1 3 5 7 9 11 13 15 17 19 21 23 Link Act 100Mbps Link Act 100Mbps Link/Act 1000M 2 4 6 8 10 12 14 16 18 20 22 24 2 4 6 8 10 14 12 10/100Mbps 16 18 20 22 24 GIGA2 10/100/1000Mbps PORT AND SYSTEM STATUS LEDS The switch includes a display panel for key system and port indications that simplify installation and network troubleshooting. The LEDs, which are located on the front panel, are described in the following table. Table 1: System and Port Status LEDs LED Power Condition On Green Off Link/Act On/Flashing Green Off 100Mbps On Green Off Status The internal power supply is operating normally. The port is operating at 10 Mbps. ­ 13 ­ Rear Panel CHAPTER 2 | Hardware Description Table 1: System and Port Status LEDs (Continued) LED 1000M Condition On Green Off Status The port is operating at 1000 Mbps. The port is operating at 10 or 100 Mbps. RJ-45 PORTS The switch contains 24 10/100 Mbps RJ-45 ports and 2 10/100/1000 Mbps RJ45 ports. All ports support automatic MDI/MDI-X operation, so you can use straight-through cables for all network connections to PCs or servers, or to other switches or hubs. Each of these ports support auto-negotiation, so the optimum transmission mode (half or full duplex), and data rate (10, 100 or 1000 Mbps) is selected automatically. Each port also supports IEEE 802. 3x auto-negotiation of flow control, so the switch can automatically prevent port buffers from becoming saturated. REAR PANEL The rear panel of the switch features the AC power socket. Figure 3: SMCFS2601 Switch Rear Panel 100-240V~ 50/60Hz 0. 6A AC POWER SOCKET Connect the female connector of the power cord to the socket on the switch, and the male connector to the AC power outlet. Make sure the voltage of the power supply meets the requirement of the input voltage. ­ 14 ­ 3 INSTALLING THE SWITCH Before installing the switch, verify that you have all the items listed under "Package Contents. " If any of the items are missing or damaged, contact your local SMC distributor. Also be sure you have all the necessary tools and cabling before installing the switch. PACKAGE CONTENTS The following contents should be found in your package: One SMCFS2601 Switch One power cord This User Guide Rackmount Kit Four rubber foot pads SMC Warranty Card ­ 15 ­ CHAPTER 3 | Installing the Switch Precautions PRECAUTIONS To ensure long-term and stable performance of the switch, pay attention to the following before installation. SAFETY REQUIREMENTS Before cleaning the switch, disconnect the power supply. Do not clean the switch using a wet cloth, and never use any other liquid for cleaning. Take waterproof measures during storage, transportation and operation of the equipment. [. . . ] If you still cannot isolate the problem, the internal power supply may be defective. ­ 21 ­ Installation APPENDIX A | Troubleshooting INSTALLATION Verify that all system components have been properly installed. If one or more components appear to be malfunctioning (such as the power cord or network cabling), test them in an alternate environment where you are sure that all the other components are functioning properly. ­ 22 ­ B SPECIFICATIONS PHYSICAL CHARACTERISTICS STANDARDS IEEE 802. 3 10BASE-T IEEE 802. 3u 100BASE-TX IEEE 802. 3ab 1000BASE-T TOPOLOGY Star PROTOCOL CSMA/CD DATA TRANSFER RATE Ethernet: 10 Mbps (half/full duplex) Fast Ethernet: 100 Mbps (half/full duplex) Gigabit Ethernet: 1000 Mbps (full duplex) NETWORK MEDIA (CABLE) 10BASE-T: UTP Category 3, 4, 5 cable (maximum 100 m) EIA/TIA-568 100 STP (maximum 100 m) 100BASE-TX: UTP Category 5, 5e cable (maximum 100 m) EIA/TIA-568 100 STP (maximum 100 m) 1000BASE-T: UTP Category 5e, 6 cable (maximum 100 m) EIA/TIA-568 100 STP (maximum 100 m) NUMBER OF PORTS 24 10/100 Mbps and 2 port 10/100/1000 Mbps auto-negotiation RJ-45 ports ­ 23 ­ APPENDIX B | Specifications Physical Characteristics LED INDICATORS Power, Link/Act, 100Mbps, 1000M TRANSFER METHOD Store-and-Forward MAC ADDRESS LEARNING Automatically learning, automatically aging FRAME FILTER RATE 10BASE-T: 14880 pps/port 100BASE-TX: 148800 pps/port 1000BASE-T: 1488000 pps/port FRAME FORWARD RATE 10BASE-T: 14880 pps/port 100BASE-TX: 148800 pps/port 1000BASE-T: 1488000 pps/port SWITCHING DATABASE 8K MAC address entries BUFFER MEMORY 2. 5 Mbits/device SWITCHING CAPACITY 8. 8 Gbps THROUGHOUT 6. 5 Mpps ­ 24 ­ APPENDIX B | Specifications Physical Characteristics POWER SUPPLY 100 to 240 V, 50-60 Hz, 0. 6A DIMENSIONS 44 x 18. 0 x 4. 4 cm (17. 4 x 7. 11 x 1. 73 in) WEIGHT 2. 4 Kg (5. 28 lbs) FEATURE Auto­MDI/MDIX Green Saving IEEE 802. 1p QoS TEMPERATURE Operating: 0 °C to 40 °C (32 to 104 °F) Storage: -40 °C to 70 °C (-40 to 158 °F) HUMIDITY Operating: 10% to 90% (non-condensing) ­ 25 ­ APPENDIX B | Specifications Physical Characteristics ­ 26 ­ SMC NETWORKS TECHNICAL SUPPORT From Singapore in English and Tel: +65-63387667, Ext. [. . . ]