User manual SMC FS26

[. . . ] INSTALLATION GUIDE ta SMCFS26 EZ SwitchTM 10/100 24-Port Fast Ethernet Switch with 2 Gigabit uplinks EZ Switch 10/100 Installation Guide From SMC's EZ line of low-cost workgroup LAN solutions 20 Mason Irvine, CA 92618 Phone: (949) 679-8000 May 2007 Pub. # 150200062500A E052007-AP-R01 Information furnished by SMC Networks, Inc. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. [. . . ] Danemark: Suisse: Europe La prise mâle d'alimentation doit respecter la section 107-2 D1 de la norme DK2 1a ou DK2 5a. La prise mâle d'alimentation doit respecter la norme SEV/ASE 1011. La prise secteur doit être conforme aux normes CEE 7/7 ("SCHUKO") LE cordon secteur doit porter la mention <HAR> ou <BASEC> et doit être de type HO3VVF3GO. 75 (minimum). Bitte unbedingt vor dem Einbauen des Switches die folgenden Sicherheitsanweisungen durchlesen: WARNUNG: Die Installation und der Ausbau des Geräts darf nur durch Fachpersonal erfolgen. · Das Gerät sollte nicht an eine ungeerdete Wechselstromsteckdose angeschlossen werden. This is achieved though the following means: · Adherence to national legislation and regulations on environmental production standards. · Waste reduction and safe disposal of all harmful un-recyclable by-products. · Design of products to maximize recyclables at the end of the product's life span. · Continual monitoring of safety standards. End of Product Life Span This product is manufactured in such a way as to allow for the recovery and disposal of all included electrical components once the product has reached the end of its life. Manufacturing Materials There are no hazardous nor ozone-depleting materials in this product. Documentation All printed documentation for this product uses biodegradable paper that originates from sustained and managed forests. The inks used in the printing process are non-toxic. Purpose This guide details the hardware features of the switches, including their physical and performance-related characteristics, and how to install each switch. Audience This guide is for system administrators with a working knowledge of network management. Zielgruppe Dieser Anleitung ist fuer Systemadministratoren mit Erfahrung im Netzwerkmangement. Sie sollten mit Switch- und Netzwerkkonzepten vertraut sein. viii Contents Introduction Features and Benefits Front and Rear Panels Rear Panel Front Panel RJ-45 Ports 1000BASE-T Ports LED Status Indicators Installing the Switch Package Contents Selecting a Site Instructions Applications Rack Mounting Product Specifications Physical Characteristics Switching Criteria Troubleshooting Diagnosing Switch Indicators Power and Cooling Problems Installation Cables Twisted-Pair cable and Pin Assignments 10BASE-T/100BASE-TX Pin Assignments Straight-Through Wiring Crossover Wiring 1000BASE-T Pin Assignments 1 1 1 1 1 2 2 3 3 3 3 4 5 7 7 7 8 8 8 8 9 9 9 10 10 11 ix Contents x Introduction The SMC EZ Switch 10/100, SMCFS26, is a high-performance Fast Ethernet switch designed for delivering 100 Mbps connectivity to the desktop. It provides 24 fullduplex 100BASE-TX ports and two 1000BASE-T uplink ports that significantly improve network performance and boost throughput for high-bandwidth applications. With 8. 8Gbps of aggregate bandwidth, the switch provides a simple solution to meeting the growing demands on your network's limited resources. Features and Benefits · Auto-negotiation supported on all ports · Automatic MDI/MDI-X operation · IEEE Std 802. 3-2005 compliance ensures compatibility with standards-based hubs, switches and cards from any vendor · Store-and-forward switching ensures error-free transmission · Half- and full-duplex flow control prevents packets from being dropped under heavy loading · Plug-and-play nothing to configure · "At-a-glance" LEDs for port and system status monitoring · Desktop or rack installation Front and Rear Panels 1 3 5 7 9 11 13 15 17 19 21 23 2 4 6 8 10 12 14 16 18 20 22 24 25 26 100-240V~50-60Hz 0. 75A Rear Panel The AC power socket is located on the rear panel of the switch. Front Panel RJ-45 Ports This switch features 24 10/100BASE-TX ports with RJ-45 connectors located on the front panel of the switch. Because all ports support automatic MDI/MDI-X operation, you can use straight-through cables for all network connections to PCs or servers, or to other switches or hubs. 1 Introduction 1000BASE-T Ports The two 1000BASE-T RJ-45 ports operate at 10 Mbps or 100 Mbps, half or full duplex, or at 1000 Mbps, full duplex. Because these ports support automatic MDI/MDI-X operation, you can use straight-through cables for all network connections to PCs or servers, or to other switches or hubs. LED Status Indicators The front panel of the switch provides status LEDs for "at-a-glance" system monitoring. The following table details the functions of the various indicators. Port and System Status LEDs Condition Status On The switch is receiving power. On Off 10/100/1000 Flashing On Green Off Amber The port has established a valid network connection. When the corresponding Link/Act LED is on, indicates the port is operating at 10 Mbps. Indicates the port is operating at 1000 Mbps (port 25, 26) LED Power Ports 1-24 Link/Act 2 Installing the Switch Before installing the switch, verify that you have all the items listed under "Package Contents. " If any of the items are missing or damaged, contact your local distributor. Also be sure you have all the necessary tools and cabling before installing the switch. Package Contents This package includes: · · · · · EZ Switch 10/100, SMCFS26 Four rubber foot pads This Installation Guide Two mounting brackets and four screws Appropriate AC power cord Selecting a Site Be sure to follow the site selection guidelines below when choosing a location: · Select a suitable location for the switch: · It should be accessible for installing, cabling and maintaining the switch. · The temperature and humidity should be within the ranges listed in the specifications. · There should be adequate space (approximately two inches) on all sides for proper air flow. [. . . ] If you still cannot isolate the problem, then the internal power supply may be defective. Installation Verify that all system components have been properly installed. If one or more components appear to be malfunctioning (e. g. , the power cord or network cabling), test them in an alternate environment where you are sure that all the other components are functioning properly. 8 Cables Twisted-Pair cable and Pin Assignments For 10/100BASE-TX connections, the twisted-pair cable must have two pairs of wires. For 1000BASE-T connections the twisted-pair cable must have four pairs of wires. For example, one wire might be green and the other, green with white stripes. [. . . ]