User manual SMC 7908VOWBRB

[. . . ] · PPP LED - The green LED will blink when a PPP connection is being negotiated and will remain solid when a PPP connection is made and is functioning properly. Troubleshooting Installation Troubleshooting · Check that the Power Adapter is both plugged into a working power socket and connected to the Router. · The wired PC should connect to a LAN port of the Router using an Ethernet cable. · The Router ADSL port should be connected to your phone socket on the wall. The DSL LED should be on when there is a valid connection to your ISP. [. . . ] Cables of this type can be purchased at most computer retailers. Wireless Troubleshooting · Check that the SSID is the same on the Router and the wireless PC. · Check that the wireless encryption is the same on the Router and the wireless PC. To help debug a problem, turn off encryption in both the Router and wireless PC until you can establish a connection. · The wireless PCs must be set to Infrastructure mode to work with a Router. · If your computer has both a wired and wireless connection installed, ensure that the wired Ethernet cable is unplugged. · Check that the Router WLAN LED is on, to indicate that Wireless networking is enabled. To enable wireless networking, go to the Router Wireless page and enable Wireless Networking. · If there are a number of wireless networks within range, then you may experience poor wireless performance if the wireless channels are too close together. Ideally, neighbouring wireless networks should be at least 5 channels apart. · The Router has a feature called MAC Filter which controls which wireless PCs have access to the wireless LAN. If this feature is enabled, then ensure that the MAC address of your wireless PC card is listed in the MAC Filter page. Information furnished by SMC Networks, Inc. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties, which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications at any time without notice. SMC is a registered trademark; and BarricadeTM is a trademark of SMC Networks, Inc. Other product and company names are trademarks or registered trademarks of their respective holders. and Canada (24 hours a day, 7 days a week) (800) SMC-4-YOU Phn: (949) 679-8000 Fax: (949) 679-1481 From Europe : Contact details can be found on www. smc. com INTERNET E-mail addresses: techsupport@smc. com Driver updates: http://www. smc. com/index. cfm?action= techsupport drivers downloads World Wide Web: http://www. smc. com/ If you are looking for further contact information, please visit www. smc. com 38 Tesla Irvine, CA 92618 Phone: (949) 679-8000 Model Number: SMC7908VoWBRB TM ADSL BarricadeTM g Broadband Voice Router with Built-in Annex B ADSL2/2+Modem Hardware e Installation Hardware Ins allation Hardwar Installation Hardware Thank you for choosing the SMC Barricade ADSL Wireless Broadband Voice Router. This Quick Installation Guide will enable you to have your new router up and running in a few minutes. The Router should be located in a central position relative to the wireless PCs that will connect to it. A suitable location might be on a high shelf or a similar position that allows good wireless coverage from the Router to the wireless PCs. TM Initial Configuration Follow the steps in this section after you have connected your hardware as described in the Hardware Installation section. Before beginning, make sure you have all the details about your internet connection from your ISP. Note: On first power-up or immediately following a Restore to Factory Defaults, the wireless is turned off. [. . . ] SSID or WEP) of your Router from a wireless PC, then you may lose contact with your Router. To re-establish the wireless connection, change the wireless settings of your PC to be the same as the Router. 5. To create a wireless network, the Router and wireless PCs must have the same SSID and encryption settings. The default wireless settings for the Router are shown below: · SSID - Router default is SMC The SSID is the name given to your wireless LAN. [. . . ]