User manual SMC 7904WBRA-N

[. . . ] ADSL2 Barricade N Draft 11n Wireless 4-port Annex A ADSL2/2+ Modem Router SMC7904WBRA-N Router with built-in ADSL2/2+ Modem From SMC's line of award-winning connectivity solutions 20 Mason Irvine, CA 92618 Phone: (949) 679-8000 May 2008 R. 02 F/W 0. 11 Information furnished is believed to be accurate and reliable. However, no responsibility is assumed by our company for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of our company. We reserve the right to change specifications at any time without notice. [. . . ] The IP address of the time server. Wireless mode Channel Time Zone Parameters Time Zone NTP Primary server Secondary server 4-15 CONFIGURING THE BARRICADE Parameter ISP Protocol VPI/VCI Description The name of the ISP you have selected from list. If you are unsure if the selected protocol is correct check with your ISP. If you are unsure the VPI/VCI values are correct check with your ISP. ADSL Operation Mode (WAN) AAL5 Encapsulation Shows the packet encapsulation type. If you are unsure the selected Encapsulation is correct check with your ISP. Network Layer Parameters (WAN) IP Address Subnet Mask Default Gateway DNS Server WAN IP address (only displayed if you have static IP). If the DNS address field was left blank in previous steps the address will be displayed as 0. 0. 0. 0. The password (hidden). ISP Parameters Username Password If the parameters are correct, click FINISH to save these settings. Go to "Troubleshooting" on page A-1 if you cannot make a connection to the Internet. 4-16 CONFIGURATION PARAMETERS Configuration parameters There are 13 main menu items located on the left side of the screen. Each main menu item is described in the following table. Menu System Description Sets the local time zone, the password for administrator access, and the IP address of a PC that will be allowed to manage the Barricade remotely. Sets the TCP/IP configuration for the Barricade LAN interface and DHCP clients. Configures a variety of security and specialized functions including: Access Control, URL blocking, Internet access control scheduling, intruder detection, and DMZ. Configures Dynamic DNS function. WAN LAN Wireless NAT Routing Firewall SNMP UPnP ADSL DDNS 4-17 CONFIGURING THE BARRICADE Menu Tools Description Contains options to backup & restore the current configuration, restore all configuration settings to the factory defaults, update system firmware, or reset the system. Provides WAN connection type and status, firmware and hardware version numbers, system IP settings, as well as DHCP, NAT, and firewall information. Displays the number of attached clients, the firmware versions, the physical MAC address for each media interface, and the hardware version and serial number. Shows the security and DHCP client log. Status 4-18 CONFIGURATION PARAMETERS System Time Zone Select your local time zone from the drop down menu. This information is used for log entries and client filtering. For accurate timing of log entries and system events, you need to set the time zone. If daylight savings is used in your area, check the box to enable the function, and select the start/end dates. If you want to automatically synchronize the ADSL router with a public time server, check the Enable Automatic Time Server Maintenance box. Select the desired servers from the drop down menu. 4-19 CONFIGURING THE BARRICADE Password Settings Use this screen to change the password for accessing the management interface. Passwords can contain from 3~12 alphanumeric characters and are case sensitive. Note: If you lost the password, or you cannot gain access to the user interface, press the blue reset button on the rear panel, holding it down for at least 10 seconds to restore the factory defaults. Enter a maximum Idle Time Out (in minutes) to define a maximum period of time for which the login session is maintained during inactivity. If the connection is inactive for longer than the maximum idle time, it will perform system logout, and you have to log in again to access the management interface. [. . . ] This is caused by a conflict with beacon packet element ID 221 used by the WPS protocol and Windows Zero Configuration (WZC) service. Please visit Microsoft download center for upgrading the WZC: Wireless LAN API (KB918997) at http://www. microsoft. com/downloads/details. aspx?Fa milyID=52a43bab-dc4e-413f-ac71158efd1ada50&DisplayLang=en 2. Check Disabled and click Apply Changes on Wi-Fi Protected Setup (WPS) screen. See "WPA" on page 4-38 for configuring WPA/WPA2PSK security. [. . . ]