User manual SMC 7800A/VCP

[. . . ] TigerAccessTM EE Ethernet-over-VDSL2 CPE High-speed Internet access over existing phone lines Concurrent data/phone services over single connection Always-on digital connection provides quick initialization Seamless rate adaptation enhances quality in video applications Supports PC or Mac with Ethernet adapter card installed Installation Guide SMC7800A/VCP TigerAccess-EE CPE Installation Guide From SMC's Tiger line of feature-rich workgroup LAN solutions 20 Mason, Irvine, CA 92618 Phone: (949) 679-8000 February 2007 Pub. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications at any time without notice. [. . . ] Range 100 Mbps 80/35 Mbps Symmetric Asymmetric 200 m (656 ft) 300 m (984 ft) · · Concurrent data and telephone services (voice/ISDN) over a single connection Always-on digital connection eliminates dial-up delays, providing transparent reconnection when initiating a network request 1-4 SYSTEM REQUIREMENTS · Supports ITU-T VDSL/VDSL2 and ANSI T1E1. 4 Part 1 VDSL interface standards, as well as other evolving ETSI, ANSI, and ITU VDSL standards for the copper local loop Spectral compatibility with VDSL, VDSL2, ADSL, ADSL2+, ISDN (2B1Q/4B3T), Smartphone digital PBX extensions and narrowband interference Robust operation on severely distorted lines Supports power back-off algorithm that permits a mixed distance deployment LEDs indicate VDSL link status, and power Simple plug-and-play installation · · · · · Additional VDSL2 features (CPE side) include: · · · · · Fast startup for quick initialization Trellis coding modulation for higher performance Seamless rate adaption for enhanced quality in video applications Variable tone spacing enables best performance for long and short reach lines Improved framing, overhead channel, and interleaving System Requirements Before you start installing the CPE, make sure you can provide the right operating environment. See the following installation requirements: · · A PC or Macintosh with a 10/100 Mbps Ethernet adapter card installed. For Internet access, the computer must be configured for TCP/IP. 1-5 ABOUT THE TIGERACCESS-EE CPE · Power requirements: 12 VDC via the included AC power adapter. Make sure that a properly grounded power outlet is within 1. 8 m (6 ft) of the CPE. The CPE should be located in a cool dry place, with at least 5 cm (2 in. ) of space on all sides for ventilation. Place the CPE out of direct sunlight, and away from heat sources or areas with a high amount of electromagnetic interference. The temperature and humidity should be within the ranges listed in the specifications. Be sure that the CPE is also accessible for the Ethernet and telephone cabling. · · · 1-6 CHAPTER 2 HARDWARE DESCRIPTION Unpacking After unpacking this CPE, check the contents to be that sure you have received all the components. Then, before beginning the installation, be sure that you have all other necessary installation equipment. Please inform your dealer if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including the original packing materials. Use them again to repack the product in case there is a need to return it for repair. 2-1 HARDWARE DESCRIPTION Front and Rear Panel This device is an external VDSL2 CPE for high-speed Internet access applications. The front panel of the CPE provides an array of system and port status indicators. The rear panel includes ports for the VDSL line, a 10/100 Mbps Ethernet connection to a computer, and an RJ-11 phone jack for connection to a telephone. The following figure shows the external components of the CPE: System Indicators Ethernet Status Port Link/Activity TigerAccess - EE CPE SMC7800A / VCP DIAG POWER SPEED DUPLEX VDSL LAN VDSL Port Phone Port DIP Switches Ethernet Port DC Power Jack Figure 2-1 Front and Rear Panels 2-2 SYSTEM AND PORT STATUS LEDS System and Port Status LEDs The CPE includes key system and port indications that simplify installation and network troubleshooting. The LEDs, which are located on the front panel for easy viewing, are described in the following table. Table 2-1 System and Port Status LEDs LED Status On Off On Off Flashing Description Power is being supplied to the CPE. A failure has been detected during bootup (including self-test failure or other problem). CPE is transmitting or receiving data on this port. System Status Indicators POWER DIAG* Port Status Indicators SPEED DUPLEX VDSL* On Off On Off On Off Flashing LAN On Off Flashing * These LEDs also turn on when firmware is being updated. 2-3 HARDWARE DESCRIPTION 2-4 CHAPTER 3 INSTALLATION Installation Overview Before installing the CPE, verify that you have all the items listed in the "Unpacking" on page 2-1. If any of the items are missing or damaged, contact your local distributor. Also, be sure you have all the necessary tools and cabling before installing the CPE. Cable Connections Depending on the wiring configuration used in your house, separate wall jacks may be used for telephone and VDSL services. Otherwise, you will need to connect telephones and your computer directly to the CPE. VDSL Line Wall Jack RJ-11 Ports RJ-45 Port AC Power Outlet AC Power Adapte Standard Telephone Cable Computer Telephone, Fax, or Modem Category 5 UTP cable to Ethernet port on computer Figure 3-1 Connecting the CPE 3-1 INSTALLATION 1. Using standard telephone cable, connect the CPE's RJ-11 LINE port to the RJ-11 telephone wall jack providing the VDSL service. [. . . ] DHCP is based on the Bootstrap Protocol (BOOTP), adding the capability of automatic allocation of reusable network addresses and additional configuration options. End Station A workstation, server, or other device that does not forward traffic. Glossary-1 GLOSSARY Ethernet A network communication system developed and standardized by DEC, Intel, and Xerox, using baseband transmission, CSMA/CD access, logical bus topology, and coaxial cable. The successor IEEE 802. 3 standard provides for integration into the OSI model and extends the physical layer and media with repeaters and implementations that operate on fiber, thin coax and twisted-pair cable. Fast Ethernet A 100 Mbps network communication system based on Ethernet and the CSMA/CD access method. [. . . ]