User manual SMC 2209USB/ETH

[. . . ] However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications at any time without notice. Trademarks SMC is a registered trademark; and EZ Connect and EZ Hub are trademarks of SMC Networks, Inc. [. . . ] The system BIOS may not be USB compatible or your PC's USB settings may not be enabled. Check with the motherboard manufacturer on how to enable this setting in the BIOS. Also check for the latest BIOS upgrade and perform the update if necessary. You have tried swapping cables and confirmed that proper power is being supplied to your network switch/router and you still cannot get connected to the network. o You may need to configure the adapter to connect at a specific speed. In Windows 98 and Me, right-click Network Neighborhood or My Network Places. Double-click the SMC2209USB/ETH adapter, go the "Advanced" tab and select "Connection Type". On the right, change the option to "10BaseT (Twisted Pair)". o In Windows 2000 and XP, right-click My Computer and click "Properties". Go to the "Hardware" tab and click "Device Manager". Change the "Connection Type" to "10BaseT (Twisted Pair)" and click "OK" to exit and apply the changes. Try other connection types as well if the problem still exists. · · · · 8 | Cable Types and Specifications Cable 10Base-T 100Base-TX Cable Types and Specifications Type Max. 5 100-ohm UTP 100 m (328ft) Connector RJ-45 RJ-45 Twisted-Pair Cable and Pin Assignments DO NOT plug a phone jack connector into any RJ-45 port. Use only twisted-pair cables with RJ-45 connectors that conform with FCC standards. For 10Base-T / 100Base-TX connections, a twisted-pair cable must have two pairs of wires. For example, one wire might be red and the other red with white stripes. Caution: Each wire pair must be attached to the RJ-45 connectors in a specific orientation. The figure below illustrates how the pings on the RJ-45 connector are numbered. Be sure to hold the connectors in the same orientation when attaching the wires to the pins. With 10Base-T/100Base-TX cable, pins 1 and 2 are used for transmitting data, and pins 3 and 6 for receiving data. The "+" and "-" signs in the table below are used to represent the polarity of the wires that make up each wire pair. Pin 1 2 3 6 RJ-45 Pin Assignments Assignment Tx+ TxRx+ Rx- 9 | Technical Specifications Standards: IEEE 802. 3 10Base-T IEEE 802. 3u 100Base-TX IEEE 802. 3x 100Base-TX Flow Control support Host Interface: USB 1. 0/1. 1, 2. 0 Ports: One USB Type A / Male Connector One RJ45 port for 10Base-T and 100Base-TX LED: 10/ACT, 100/ACT, F/H Operating Systems: Windows 98, Me, 2000, XP Environment: Operating: Temp 0-50°C / Humidity 10-90% Storage: Temp -20-65°C / Humidity 10% - 90% Dimensions: 74. 5 x 28. 1 x 15. 1 (L x W x H) Power Consumption: - 10 Mbps mode: Max 293 mA @5V - 100 Mbps mode: Max 300 mA @5V Compliances/Certifications: FCC Part 15 Class B CISPR PUB. 22 EN55022: 1994/A1: 1995/A2: 1997 Class B EN61000-3-2: 2000 EN61000-3-3: 1995/A1: 2001 EN55024: 1998/A1: 2001 EN61000-4-2: 1995 IEC 61000-4-2: 1995 IEC 61000-4-3: 1995 IEC 61000-4-4: 1995 IEC 61000-4-5: 1995 IEC 61000-4-6: 1996 IEC 61000-4-8: 1993 IEC 61000-4-11: 1994 10 | Terminology 10BaseT - Physical Layer Specification for Twisted-Pair Ethernet using Unshielded Twisted Pair wire at 10Mbps. This is the most popular type of LAN cable used today because it is very cheap and easy to install. It uses RJ-45 connectors and has a cable length span of up to 100 meters. [. . . ] MDI / MDI-X - Medium Dependent Interface - Also called an "uplink port, " it is a port on a network hub or switch used to connect to other hubs or switches without requiring a crossover cable. The MDI port does not cross the transmit and receive lines, which is done by the regular ports (MDI-X ports) that connect to end stations. There are typically one or two ports on a device that can be toggled between MDI (not crossed) and MDI-X (crossed). Medium Dependent Interface ­ X (crossed) - A port on a network hub or switch that crosses the transmit lines coming in to the receive lines going out. [. . . ]