User manual SMART-CLIP SMART-CLIP

[. . . ] Smart-Clip firmware can be upgraded through the Internet in real-time using our ActiveX plugin. Upgrades include latest firmware AND additional phone vendors/models support. (NOTE: Motorola upgrades are FREE OF CHARGE) FEATURES CURRENTLY IN DEVELOPMENT · · · Direct special function to repair phones using full flashing Direct JTAG function to repair phones with lost boot zone Direct JTAG function for testing CPU/RAM/FLASH Features listed above will be available via upgrades free of charge for Motorola 2004 © Copyright GsmServer Team OPERATION INSTRUCTION 1. [. . . ] Don't disconnect phone from Smart-Clip while green led indicator blinks!The phone is unlocked. 2004 © Copyright GsmServer Team MOTOROLA AXXX/EXXX/VXXX UNLOCKING NOTE: Don't unplug cable right after phone reboot, wait until E/G led stops blinking! MOTOROLA E396/E398 UNLOCKING NOTE: Remove flash card from phone before unlocking MOTOROLA C115/C116/E365 UNLOCKING PROCEDURE: Power off the phone Connect clip to the phone Press UNLOCK button Press Power button on the phone within 5 seconds after you press UNLOCK button on a clip. Connect Smart-Clip to PC using LPT cable Power Smart-Clip ON (warning: don't use battery!) Go to our Upgrade Zone Upgrade Zone uses ActiveX element, answer "Yes" to install and run it Press "Connect" Press "Update" if your version is out of date Power Smart-Clip OFF Disconnect LPT cable 2004 © Copyright GsmServer Team USING SMART-CLIP READER (SCReader. exe) 1. Connect Smart-Clip to PC using LPT cable Power Smart-Clip ON (warning: don't use battery!) Run SCReader. exe (WinXP/2k with admin rights) Press "Connect" Press "Read history", save to file Press "Read flash", save to file Close Smart-Clip Reader Power Smart-Clip OFF Disconnect LPT cable Send history and phone flash files to support@smart-clip. com TROUBLESHOOTING If you have any trouble upgrading your clip, please check the following requirements: firewall on your computer is disabled or configured properly you have reliable internet connection your LPT cable works properly LPT port settings are set to EPP in BIOS you use a stable power supply (adapter) with your clip your Internet Explorer version is not lower than v5. 0 if you use Win XP, log in as administrator If you have problems updating under Win XP please download Porttalk file, unzip it and run install. bat file. If you have problems with update make a screenshot of update report and email immediately to support@smart-clip. com If you encounter unlock problems make sure that: First of all, make sure the phone model you are trying to unlock is in the list of supported models. If it is, you need to make sure the phone you are unlocking is charged to its full battery capacity and that battery connection poles are clean. Remove 4 front-panel screws Take PCB out of the box carefully Solder LPT and USB ports to ground (reference picture below) Assemble clip 2004 © Copyright GsmServer Team FAQ Does Smart-Clip need to be activated?However, it may happen that by the time you have Smart-Clip there is a newer version of firmware available for it. You can update your clip easily by going to http://www. smart-clip. com/upgrade. php and running "Smart-Clip Online Updater". Smart-Clip update system is organized in such way that you do not need to register for update. Every owner can go to support page and connect his/her clip using "Smart-Clip Online Updater". When the program asks you if you want to install and run "Smart-Clip Online Updater" answer "yes". Rather it is a platform for ongoing solutions constantly developed by GsmServer team. Similar to Griffin and Twister Smart-Clip stays efficient all the time by means of available updates. Normally all LPT ports are set by default to operate in Smart-Clip friendly way. However, if your LPT configurations have been changed you should know that 2004 © Copyright GsmServer Team bidirectional modes (EPP, ECP) are required for Smart-Clip update to operate properly. [. . . ] In order to successfully update your clip (or use SCReader. exe) under Windows XP you need to enter the system as an Administrator (or as a user with administrative rights). First of all, make sure the phone model you are trying to unlock is in the list of supported models. If it is, you need to make sure the phone you are unlocking is charged to its full battery capacity and that battery connection poles are clean. [. . . ]