User manual SLAUTTERBACK SS10G MARK II PRODUCT MANUAL

[. . . ] ® Super Squirt SS10G Mark II Product Manual Manual Number: 19600-133 Revision: C ® Super Squirt SS10G Mark II Product Manual Manual Number: 19600-133 Revision: C Date: 11/07/00 Copyright 2000 Slautterback Corporation ! WARNING To avoid personal injury and damage to equipment and property, read the product manual completely before installing, operating or servicing this equipment. Follow all safety warnings located on this product and in the product manual. Consult the safety precautions section of the product manual for an explanation of all safety symbols used on this equipment. After reading this manual, if further assistance is needed, contact your factory authorized sales or service representative. For a list of Sales and Service Centers (SSCs) in your area, Call 1-800-827-3308 or Visit our website at www. slautterback. com NOTE CONCERNING ILLUSTRATIONS: All illustrations within this product manual should be considered as general representations of the parts or assemblies depicted, and should not serve as mechanical drawings, nor be consulted for scope or scale. [. . . ] · Disconnect electrical power from external source to melt unit before undertaking maintenance or troubleshooting. · Depressurize system before performing any maintenance to pump, pump filter, flow control valve or hose. Turn pump switch off and depress trigger on handgun until there is no flow. Air trapped in the system or in a component can form a pressure pocket. · Always read the manufacturer's recommended use of the material. 1. 5. 6. 7. Become familiar with Section 5. 1, Controls and Indicators. Turn melt unit on and allow sufficient warmup time for hot melt material to thoroughly melt. To prevent motor stalling, adjust flow control valve to the minimum flow requirement. 12 Super Squirt SS10G Mark II 19600-133 Rev. C 11/07/00 Copyright 2000 Slautterback Corporation 5. 3 Adjustments 5. 3. 1 Tank Temperature Controller 1. To prevent hot melt degradation, set melt tank temperature to the minimum temperature specified by hot melt manufacturer. To raise melt tank temperature, turn tank temperature controller adjustment shaft [1] clockwise with screwdriver. To lower melt tank temperature, turn adjustment shaft [1] counter-clockwise with screwdriver. The melt tank temperature controller range is 260 °C (500 °F) for one 320° rotation of the adjustment shaft. Allow melt tank temperature to stabilize 30 minutes before adjusting further. 6. 5. 3. 2 Hose Temperature Controller Temperature graduations on hose controller reflect approximate hose temperature. Hose temperature should be the minimum temperature required for application to prevent degradation of material in the hose and maximize hose life. To raise hose temperature, turn adjustment shaft [2] clockwise with screwdriver to desired temperature on dial. To lower hose temperature, turn adjustment shaft [2] counterclockwise with screwdriver to desired temperature on dial. Refer to Temperature Check in Maintenance section of the handgun manual. 2. 3. 4. 5. 2 1 © Copyright 2000 Slautterback Corporation Super Squirt SS10G Mark II 19600-133 Rev. C 11/07/00 2000008a 13 5. 3. 3 Adhesive Flow Adjustment ! CAUTION: For maximum performance and motor life, do not allow pump motor to stall. A prolonged stall condition will cause motor to go into thermal overload. Flow Control Valve An adjustable pressure regulating device is mounted on the pump under the melt unit chassis. [. . . ] Breaker, 2. 9 Amp Fast Trip Capacitor, 10 µf 370 VAC Spacer, 4 ID x 0. 44 OD x 44. 45 mm (1. 75 in. ) (4) Wire nuts Screw, Shc; 1/4-20 X 3 Lg (4) Washer, split lock, 6. 35 mm (0. 25 in. ) (4) Nut, 1/4-20 hex (4) Part Number 73714-24 70460-4 14475-7 12055A-29 18416-1 14471-4 12277-2 14431-GDT 14451-GA 14441-GA * NOTE: does not include pump On/Off switch/circuit breaker or capacitor. 3 6 9 1, 2 5 4 7, 8 2000353 30 Super Squirt SS10G Mark II 19600-133 Rev. C 11/07/00 Copyright 2000 Slautterback Corporation 9. 5 L2 Handgun Nozzles Item Description (Quantity) L2 Nozzle, 3/16" spacing L2 Nozzle, 1/4" spacing L2 Nozzle, 5/16" spacing L2 Nozzle, 3/8" spacing L2 Nozzle, 7/16" spacing L2 Nozzle, 1/2" spacing L2 Nozzle, 9/16" spacing L2 Nozzle, 5/8" spacing L2 Nozzle, 11/16" spacing L2 Nozzle, 3/4" spacing L2 Nozzle, Extended General Purpose, 1 orifice Part Number 70218-3 70218-4 70218-5 70218-6 70218-7 70218-8 70218-9 70218-10 70218-11 70218-12 70234-1 NOTE: The L2 nozzle spacing dimension equals the space between the two panes of glass in a finished insulated window. © Copyright 2000 Slautterback Corporation Super Squirt SS10G Mark II 19600-133 Rev. C 11/07/00 31 9. 6 Recommended Spares Item Heaters Kit, tank heater, 115 VAC, 400 W Standard Melt Unit Switches Kit, tank controller, 38­232 °C (100­450 °F) Kit, hose controller, 177­232 °C (350­450 °F) Kit, tank overtemperature thermostat, 232 °C (450 °F) Circuit breaker, 115 VAC, 15 A Pump motor ON/OFF switch, 115 VAC, 2 A Pump warmup thermostat 121 °C (250 °F) Kit, tank thermometer Pump Kit, pump, V1-675 Kit, hardware pump, V1 Kit, pump seal, V1 (includes hardware) Motor Motor group, 38/31 rpm, 115 VAC, 60/50 Hz Capacitor, 10 µf, 370 VAC Coupler, pump shaft-motor Key, machine 4. 76 mm (0. 1875 in. ) square x 5. 08 cm (2 in. ) long Pump shaft assembly Kit, idler gear, SS10G Chain assembly, SS10G Wire nuts, medium low temperature L2 Standard Handgun/Hose Assemblies - Capillary Control L2 Handgun/hose, 2. 44 m (8 ft), 232 °C (450 °F), 115 VAC L2 Handgun/hose, 2. 44 m (8 ft), 232 °C (450 °F) 115 VAC 75086-000 75086-200 73714-24 18416-1 70460-4 14475-7 73167-2 79094 73164 12277-2 79048-3 79042 79081 79006 79125-4 79126-450 12015-1 12055-2 79056-1 79014 79005 Description (Quantity) Part Number 32 Super Squirt SS10G Mark II 19600-133 Rev. C 11/07/00 Copyright 2000 Slautterback Corporation Item Heated Supply Hoses Description (Quantity) Hose, L2, capillary, 2. 44 m (8 ft), 232 °C (450 °F), 115 VAC Hose, L2, capillary, 3. 66 m (12 ft), 232 °C (450 °F), 115 VAC L2 standard handgun spare, 115 VAC Kit, L2 heater, 115 VAC Kit, microswitch for L2 handgun L2 standard handgun spare, 115 VAC Constant tension balancer, 1­4 Ib Constant tension balancer, 2­5 Ib Hose hammock Swivel subassembly Needle packing washer Teflon needle seal Fiber washers Teflon seat plate Screw, seat plate Part Number 26269 08-N 26269-12-N 75085-000 79075-1 79095 75085-000 11030 11031 30087 73161 16528-18 16528-17 16528-25 16528-22 16528-23 © Copyright 2000 Slautterback Corporation Super Squirt SS10G Mark II 19600-133 Rev. [. . . ]