User manual SKYMASTER DIGITAL SATELLITE RECEIVER DS 66

[. . . ] Digital Satellite Receiver DS 66 39708-A OPERATING INSTRUCTIONS DS 66 A 7 3 4 2 5 1 6 B 2 1 8 3 4 6 5 7 9 5 D DISH C 1 2 3 4 6 7 9 11 13 14 15 17 18 21 8 10 12 VCR TV 14 13 19 16 20 AC3/SURROUND 230 V HiFi 1. Contents You have purchased a quality receiver from the SKYMASTER® range. Our products are continuously subjected to rigorous quality inspections to ensure your enjoyment. Please note that you need a digitally-compatible satellite antenna to operate the SKYMASTER® DS 66. [. . . ] 2. 1. 3 22 kHz The 22 kHz signal is used to switch the digital LNB (out = low-band, 22 kHz = high-band). If you have selected "Digital" as the LNB type, switching occurs automatically. If you do not have a commercially available LNB, you have to adjust the settings manually at this point. 2. 1. 4 DiSEqC DiSEqC allows you to receive several satellites. If you have two LNBs, for example, that are aimed at two different satellites (ASTRA and HOTBIRD), you should use a DiSEqC switch. You can control 2, 4, 8 or 16 port switches and DiSEqC capable multiple switches. Note: on some DiSEqC switches the connections are marked with letters (A, B, C, D. . . ) instead of numbers. The OSD menu ­ reception 2. 1. 5 Polarisation Satellite signals are transmitted with horizontal or vertical polarity. You should always choose the H/V setting, which allows for reception at both levels. In very exceptional situations it may be necessary to choose only horizontal OR vertical reception, e. g. in large-scale residential systems or to receive unusual satellites. 2. 2 Automatic search To automatically search for all available transponders of a satellite position. 2. 2. 1 Satellite Choose a preconfigured satellite from the list. You also have the options of renaming the satellite (button [1]), adding a new satellite (button [2]) or deleting a satellite position (button [3]). 2. 2. 2 Search mode Decide whether you want to save only the free to air or the encrypted channels as well. 2. 2. 3 Channel search Decide whether you want to search for TV and/or radio stations. GB 13 7. The OSD menu ­ reception 2. 3 TP search To search for a single transponder. This search method is useful if you only want to save a specific channel or a specific channel package. You can obtain the reception parameters (frequencies, etc. ) on the net or from TV and specialist magazines. 2. 3. 1 Satellite Choose a preconfigured satellite from the list. Quit the list by pressing [MENU]. 2. 3. 2 TP index Displays the current transponder index number. The figure after the slash displays the satellite's total number of transponders. To add a new transponder press [1], to delete the current transponder press [2]. If you would like to delete all the selected satellite's transponders, press [3]. 2. 3. 3 TP frequency You normally enter the frequency as five digits, e. g. 12480 (MHz) or you can modify it in separate steps by pressing the [ ] buttons and confirming the new reading with [OK]. Caution: the previous readings are overwritten when you quit the menu and respond with a "YES" to the prompt for confirmation. 2. 3. 4 Symbol rate The symbol rates of the most common satellite transponders are almost always 27500 or 22000. You can change these values by entering them directly or in separate steps using the [ ] buttons. [. . . ] Use the control buttons to select one of nine channels and access it with the OK button. With the PAGE buttons (+ or -) you can display the previous or next nine TV channels. 9. Troubleshooting No Function Note the position of the mains switch and switch the unit on if necessary (3. (No signal display on the unit or via the signal displays in the OSD): 1. [. . . ]