User manual SKYMASTER ARF PLUS PRO A10

[. . . ] 1/6. 25 Scale Almost-Ready-To-Fly RC Jet Assembly and operations manual Spesifications Type : T. A. V. S ARF PRO Scale : 1/6. 25th Length : 101, 3": (2552mm) Span : 109, 6": (2784mm) Weight : 40--46 Lbs ( 19--21. 5 Kg) Engine : 2 x 22--36 Lbs (10 --12 Kg) trust Radio : 12 Channel 13--15 servo's The A-10 Warthog by Skymaster Thank you very much for purchasing our Skymaster ARF PRO A-10. Please note that the photos in this instruction manual show certain views from the prototypes. Some modifications and upgrades might have taken place by the release of the model. Many scale options are included with your model including very scale speed brakes. [. . . ] If you make use of another manufacturer, please use equipment with similar specifications!The trend nowadays is to use dual battery management systems and dual RX equipment. With the introduction of 2. 4 Ghz even quad RX systems are considered as normal for a jet model. Always center and install the correct output arms while on the bench, once the servo is in the aircraft access to the servo arm screw is sometimes limited. REMEMBER: The best equipment is only as good as the weakest link. Accessories 1. 3 JR577servos for Landing Gear, Door and Brake valves or check next line. 2 Turbine motor, with thrust range between 8kg and 10kg, with accessories. Fuel tubing, Hopper tank (or BVM UAT), festo fittings, fuel filters, fuel tube etc. If not, please read it again before you start the assembly. P-8 Kit Contents Assembly & Operation Manual Picture A Picture B Picture C Picture D A10 ARF PRO Contents: Picture A Fuselage front and rear including nose gear + door installed Fin & Rudder & Stabs & Elevators Stabilizer and Elevator Wings incl L/G + Doors installed. Incl sliding flap + Aileron + Speedbrake Engine POD Main Landing Gear Fairing Scale fittings Wing Tips Picture B Picture C Picture D P-9 Assembly & Operation Manual OPTIONAL PARTS Landing Gear Set Photo 1 3 x Air Tanks 1 x Retract Valve 2 x Filler & 2 x Pressure Gauges 1 x Electronic Brake Valve 5 x Air Tubing, 10 x Quick Disconnect 8 x T-pieces, 2 x 4 way Fan (2) Photo 2 Pushrod Set Photo 3 Photo 4 Airpower Optional 5 in 1 Electronic Valve & Sequencer Control Brake, Gear and Doors air pressure and gear fail safe. Photo 5 Stainless Steel Tail Pipe (2) Cockpit Photo 6 Photo 7 P-10 Assembly & Operation Manual Servo mounting hardware Photo 8 Photo 9 Powerbox Royal BVM UAT Photo 10 Photo 11 L/G hydraulic fluid kit Gatling Gun Photo 12 Photo 13 Tygon Tubing Tank Hardware Photo 14 Photo 15 P-11 Assembly & Operation Manual CONTROL LINKAGES Photo 16 WINGS NOTE: Make sure to have some sort of protective foam on the work bench. Check Remove factory self tapping L/G screws and replace with high quality screws. Photo 17 L/G box is removable. the operation of brake Check Remove and mark servo covers and inspect plywood. Use dremel to clean out some glue and ply to make sure servos will fit well. Photo 18 P-12 Assembly & Operation Manual all items needed to complete wings. Fit 2 L-shape Locate servo brackets to 1 x JR DS8711 servos. servo must be mounted with horns facing up. The horn Aileron must be closest to control surface and furthest away for root. Photo 19 servo horns and centre servo's with TX. Secure a line perpendicular to hinge line & mark location of horn Draw Dremel to drill 1. 5mm pilot holes and to mill slot for conUse trol horns. Photo 20 30 minute epoxy to glue control horns Use epoxy cured, insert pushrods and secure safety clips. Mill slot in servo cover and Check secure with 4 x 1mm set screws. Photo 21 INSTALLING SPEEDIF BRAKE FOLLOW FOLLOWING STEPS--OR GLUE 2 HALVES TOGETHER FOR NORMAL OPERATION. 2 x pushrods to JR8711 servos. Use tape to secure aileron in 90deg position for easy installation of speed brake servo. Photo 22 servo for speed brake function on radio and fasten servo Setup horn. The servo is installed into aileron. slots for 2 x horn and glue Cut with 30min epoxy. Leave Photo 24 P-13 Assembly & Operation Manual NOTE: Flaps are factory installed on slides utilizing bearings. The pushrods must be installed centre of each flap for best operation. up flap pushrod. Make pushrod to servo horn (long horns) and secure safety Fit clip. pushrod through hole in trailing edge and fasten Slide servo with 4 screws. Photo 25 the ball links to secure pushrods to flap. [. . . ] Make all switches and filler valves and charging sockets easy accessible A10 will come out tail heavy if you do not plan installation. It is very important The to install all equipment as far forward as possible. installed 2 x RX + 4 X ECU batteries in nose. This will always be full of fuel and will help with I have the final adjustment of CG. wire the accessory tray outside aircraft. (note--tidy up wires unlike me :-)) . Photo 61 P-24 Assembly & Operation Manual BEFORE YOU FLY It is assumed that the builder of this kit has acquired the basic skills and knowledge necessary to make a safe and functional radio control installation into a model. [. . . ]