User manual SKYMASTER A4 ARF PRO

[. . . ] 1/5. 5 Scale Almost-Ready-To-Fly RC Jet Assembly and operations manual Spesifications Type : T. A. V. S ARF PRO Scale : 1/5. 5th Length : 85. 5 " (2225mm) Span : 61": (1550mm) Weight : 25--32 Lbs ( 12. 5--14 Kg) Engine : 23--30 Lbs (10--14 Kg) trust Radio : 12 Channel 8--12 servo's) The A4 Skyhawk by Skymaster Thank you very much for purchasing our Skymaster ARF PRO A4. Please note that the photos in this instruction manual show certain views from the prototypes. Some modifications and upgrades might have taken place by the release of the model. Many scale options are included with your model including speed brakes. [. . . ] With the introduction of 2. 4 Ghz even quad RX systems are considered as normal for a jet model. Always center and install the correct output arms while on the bench, once the servo is in the aircraft access to the servo arm screw is sometimes limited. The price of servo's are far from the price of replacing the entire model. Ask yourself if this servo or link or lead etc is worthy of my trust to protect my very large investment. . . Accessories 1. 3 JR577servos for Landing Gear, Door and Brake valves or check next line. 1 Airpower EV5U valve + 1 x EV2U valve for landing gear + doors + brakes 8. Turbine motor, with thrust range between 10kg and 14kg, with accessories. Fuel tubing, Hopper tank (or BVM UAT), festo fittings, fuel filters, fuel tube etc. If not, please read it again before you start the assembly. P-8 Kit Contents Assembly & Operation Manual Photo A A4 ARF PRO Contents: Picture A Fuselage front and rear including nose gear + door installed + speed brake installed. Left and right wings incl landing gear and doors installed Left and right stabilizers and elevators Fin and rudder Carbon main spar and stab spar Pitot tubes Refueling probe Aresting hook P-9 Assembly & Operation Manual OPTIONAL PARTS Landing Gear Photo 1 3 x Air Tanks 1 x Retract Valve 2 x Filler & 2 x Pressure Gauges 1 x Electronic Brake Valve 5 x Air Tubing, 10 x Quick Disconnect 8 x T-pieces, 2 x 4 way Fuel Tank (2) 3. 5L Photo 2 Pushrod Set Photo 3 Photo 4 Airpower Optional 5 in 1 Electronic Valve & Sequencer Control Brake, Gear and Doors Photo 5 Stainless Steel Tail Pipe Cockpit P-10 Photo 6 Photo 7 Assembly & Operation Manual Servo mounting hardware Photo 8 Bolts & Accessory pack Photo 9 L/G hydrolic set Carbon Bypass Photo 10 Photo 11 Tygon Tubing Tank Hardware Photo 12 Photo 13 P-11 Assembly & Operation Manual CONTROL LINKAGES Flaps : 63mm (2) Aileron : 62mm (2) Elevator : 80mm (2) Steering: 10 mm Photo 14 WINGS NOTE: Make sure to have some sort of protective foam on the work bench. Check Remove factory self tapping L/G screws and replace with high quality screws. Inspect landing gear blocks. Make sure all parts are glued. Photo 15 quick disconnects to air line. the operation of brake Check Remove and mark servo covers and inspect plywood. Use dremel to clean out some glue and ply to make sure servos will fit well. Photo 16 P-12 Assembly & Operation Manual all items needed to complete wings. Fit 2 L-shape Locate servo brackets to 1 x JR DS8411 servos. servo must be mounted with horns facing Aileron Photo 17 up. The horn must be closest to control surface and furthest away for root. servo horns and centre servo's with TX. Drill horn 1. 5mm for link Mark Dremel to mill slot for control horns. Use 30 minute epoxy to glue control horns Use epoxy cured, insert After pushrods and secure safety clips. Photo 19 operation of aileron. Check Photo 20 Photo 21 P-13 Assembly & Operation Manual up 2 flap pushrods. Mark pushrod through hole in L/G pod and fasten Slide with safety clips Photo 23 flap horn and sand bottom. Drill 1. 5mm hole for link. line on flap in line with flap pushrod Draw location of flap horn . Take care not to mill right Mark through flap. Photo 24 good quality CA glue and accelerator to glue horn to Use flap. pushrod and insert safety clips. [. . . ] It is very important to install all equipment as far forward as possible. installed 2 x RX + 2 X ECU batteries in nose. This will always be full of fuel and will help with I have the final adjustment of CG. . P-25 Assembly & Operation Manual BEFORE YOU FLY It is assumed that the builder of this kit has acquired the basic skills and knowledge necessary to make a safe and functional radio control installation into a model. When inserting the main spar into wing, make sure it only enters the amount required. [. . . ]