User manual SITECOM WL-400

[. . . ] (Wireless) IP Camera LN-402/WL-400 Full Manual About This Guide This manual describes Internet Camera, including a description of the features, as well as the installation procedures and web configuration. Included in the manual are the operating procedures for the IPView application. 1 1. Introduction Thank you for the purchase of the Internet Camera connecting directly to an Ethernet or Fast Ethernet. It is different from the conventional PC Camera, the Internet Camera is a standalone system with built-in CPU and web-based solutions providing a low cost solution that can transmit high quality video images for monitoring. [. . . ] Getting Started with IPView This section describes the operation of the IPView SE application with detailed procedures for using the application. IPView SE is responsible for the management of preview, configuration, and searching of each camera. It is designed with a user-friendly interface for ease of control and navigation requirements as illustrated below. 53 10. 1 IPView SE control panel Minimize Exit Play Scan About Combine System Config Add Camera 54 Minimize To minimize the control panel. Exit To close IPView SE. Play To play back the recorded file. Scan To search all of the available internet cameras connected to the LAN. Combine To combine all display windows in one. About To display the information of IPView SE. 55 10. 2 How to Add a Camera Add Camera Add Camera To add a new camera, click the Add Camera button. An Add Camera dialog box will appear as illustrated below. Enter the IP Address of the camera in the specified field and click the "Add" icon to add a new camera. If you want to add a camera through the Internet, you must key in a physical IP Address. When the camera is installed behind Gateway and the Open Second Port of camera/Port Forwarding of Gateway function is enabled, the Gateway IP address has to be entered with the Port Number as below: 3. At the same time, the Gateway IP address can be replaced by URL as below: 4. If you forget the IP Address that you want to add, a dialog box will appear to notify you of the error. If you are unsure of the IP Address of the camera, you can click the "Browse" button, the Browse Camera 57 dialog box will appear with a blank screen as illustrated below. You must select the camera and click the "Add" button to add a new camera. The Add Camera dialog box will appear once again with the IP Address entered. Click the "Add" button, and the camera will be automatically added into IPView SE list view format. If the Login Camera dialog box appears, make sure to enter the correct User Name and Password and click the "OK" button. If the User Name and Password is entered incorrectly, the camera will not be added into IPView SE. 58 The above dialog box will appear only if administrator has already set up the User Name and Password in the Web Configuration setting. If you forget to highlight the camera you want to add, a dialog box will appear to notify you of the error. Make sure to save any changes you have made to keep the information updated. When the user add the Internet Camera, four icons will appear, including: "Assign IP to Camera", "Connect/Disconnect", "Erase", "Extra Information" 59 Camera Config Assign IP to Camera Connect / Disconnect Erase Motion record Schedule record Manual record Extra Information 60 10. 3 How to Change Camera Assign IP of New Camera Enter a new IP address in the following dialog box, and it will connect to new camera. 61 10. 4 How to Connect / Disconnect the Image Connect the Image Click the "Connect/Disconnect" button and the preview screen will appear with the video image. Minimize Click to minimize the display screen of the Internet Camera. Maximize Click to maximize the display screen of the Internet Camera. Always on top Click to have the display screen always appear on the top of the window. Wake up control panel Click to open the control panel again when it is closed. Rotate image Click to rotate the image of the Internet Camera. 63 Disconnect the Image Click the "Connect / Disconnect" button again, the camera will be disconnected. 64 10. 5 How to Delete a Camera Erase Camera To delete a camera, you must select the camera to delete from the IPView SE control panel. After deleting the camera, the IPView SE control panel will appear as below. 65 10. 6 Extra Information Extra Information The screen displays the camera's information. 66 10. 7 How to Adjust the Property Setting System Configure From the control panel, select the button and the dialog box will appear as shown below. Log Storage: 1. Single HDD Reserve Space This option permits reserved space by memory size from 500 MB to 1000 MB. Split Recording File From this option, you can adjust the file size for recording the video images (the default setting is 67 5MB). If the recorded video files reach the file size, video images will be recorded into another file automatically. By File Size - permits recording by file memory size from 5 MB to 50 MB. [. . . ] Some protocols are responsible for formatting and presenting and presenting data that will be transferred from file server memory to the file server's net work adapter Others are responsible for filtering information between networks and forwarding data to its destination. Still other protocols dictate how data is transferred across the medium, and how servers respond to workstation requests and vice versa. Common network protocols responsible for the presentation and formatting of data for a network operating system are the Internetwork Packet Exchange (IPX) protocol or the Internet Protocol (IP). Protocols that dictate the format of data for transferors the medium include token-passing and Carrier Sense Multiple Access with Collision Detection (CSMA/CD), implemented as token-ring, ARCNET, FDDI, or Ethernet. [. . . ]