User manual SITECOM WLM-4501

[. . . ] WLM-4501 Wireless ADSL2+ Gigabit Modem Router User Manual Version: 1. 0 Table of Contents INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1 2 3 4 KEY FEATURES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 PACKAGE CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Click "Show Active Clients" button and you can see the wireless clients connected to the router. When you finish, click `Apply Changes' to save the settings made and restart the router so the settings will take effect after it reboots. Security Settings This router provides complete wireless LAN security functions, include WEP, IEEE 802. 1x, IEEE 802. 1x with WEP, WPA with pre-shared key and WPA with RADIUS. With these security functions, you can prevent your wireless LAN from illegal access. Please make sure your wireless stations use the same security function. Parameter Encryption Description You can choose "None" to disable the encryption or select "WEP", "WPA(TKIP)", "WPA2(AES)" or "WPA2 Mixed" mode for security. When "WEP" is enabled, please click "Set WEP Key" button to choose the default key and set the four sets of WEP keys. WEP supports 64-bit and 128-bit key lengths to encrypt the wireless data. WPA(TKIP) ­ WPA uses Temporal Key Integrity Protocol (TKIP) for data encryption. TKIP utilized a stronger encryption method and incorporates Message Integrity Code (MIC) to provide protection against hackers. WPA2(AES) ­ WPA2, also known as 802. 11i, uses Advanced Encryption Standard (AES) for data encryption. WPA Mixed ­ The router supports WPA (TKIP) and WPA2 (AES) for data encryption. The actual selection of the encryption methods will depend on the clients. Every user must use a valid account to login to this wireless router before accessing the wireless LAN. Check this box to authenticates user by Use 802. 1x Authentication WEP-64Bits WEP-128Bits WPA Authentication Mode IEEE 802. 1x. WEP supports 64-bit and 128-bit key lengths to encrypt the wireless data. When "WEP64Bits" is selected, you have to enter exactly 5 ASCII characters ("a-z" and "0-9") or 10 hexadecimal digits ("0-9", "a-f") for each Key (1-4). When "WEP-128Bits" is selected, you have to enter exactly 13 ASCII characters ("a-z" and "0-9") or 26 hexadecimal digits ("0-9", "a-f") for each Key (1-4). Enterprise (RADIUS) ­ It uses an external RADIUS server to perform user authentication. To use RADIUS, enter the IP address of the RADIUS server, the RADIUS port (default is 1812) and the shared secret from the RADIUS server. Please refer to "Authentication RADIUS Server" setting below for RADIUS setting. Personal (Pre-Shared Key) ­ Pre-Shared Key authentication is based on a shared secret that is known only by the parties involved. To use WPA Pre-Shared Key, select key format and enter a password in the "Pre-Shared Key Format" and "Pre-Shared Key" setting respectively. Pre-Shared Key You may select to select Passphrase (alphanumeric format) or Format Hexadecimal Digits (in the "A-F", "a-f" and "0-9" range) to be the Pre-shared Key. For example: Passphrase: "iamguest" Hexadecimal Digits: "12345abcde" Pre-Shared Key Please enter 8-63 characters as the "Pre-Shared Key". Authentication Enter the port (default is 1812), the IP address and the RADIUS Server password of external RADIUS server are specified here. [. . . ] Click Apply to save and apply the settings. Virtual server Use the Virtual Server function when you want different servers/clients in your LAN to handle different service/Internet application type (e. g. Computers use numbers called port numbers to recognize a particular service/Internet application type. The Virtual Server allows you to re-direct a particular service port number (from the Internet/WAN Port) to a particular LAN private IP address and its service port number. Local IP This is the LAN client/host IP address that the Public Port number packet will be sent to. Start port Here the starting port number must be entered End port Here the end port number must be entered Note : The ports from the start port till the End port will be opened Click the `edit icon' to change an existing rule. [. . . ]