User manual SINGER NO. 27

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SINGER NO. 27. We hope that this SINGER NO. 27 user guide will be useful to you.


SINGER NO. 27 : Download the complete user guide (1347 Ko)

Manual abstract: user guide SINGER NO. 27

Detailed instructions for use are in the User's Guide.

[. . . ] 2 When the cover is removed from the machine, the hand attachment will be found to be out of working position, as shown in Fig. Before replacing the cover, the lever should be disengaged, and the handle placed in the position shown in Fig. 1. 5 27 & 28 Stop Motion This device a allows the hand wheel to run free, so that bobbins may be wound without operating the mechanism. To loosen the wheel hold it with the left hand and with the right hand turn the stop motion screw over towards you, as shown in Fig. [. . . ] As all machines are correctly adjusted before leaving the factory, the under tension seldom requires to be altered, but if this becomes necessary tighten the screw near the point of the shuttle (see Fig. 7) to increase the tension, or loosen it slightly to lessen the tension. Always use thread with corresponding size of needle as per Table on page 3 of cover. Fine fabrics require a light tension, while heavy materials want more tension to obtain a perfect stitch. The tension on the needle thread should be regulated only when the presser foot is down. A correct stitch can usually be obtained by varying the tension on the needle thread (see Fig. 12). 14 27 & 28 To Alter the Length of Stitch Turn the thumb screw inwards (see Fig. To Change the Pressure on Material For ordinary family sewing it is seldom necessary to change the pressure on the material. If sewing fine silk or flimsy material, lighten the pressure by giving the thumb screw (1, Fig. To Turn a Corner Stop the machine when the needle is rising, but still in the material. Raise the presser foot and turn the work, using the needle as a pivot. To Sew Flannel or Bias Seams Use a short stitch and as light a tension as possible on the needle thread, so that the stitching will be loose enough to allow the material to stretch. FIG. 14 To ensure easy running the machine requires to be oiled so that all moving parts in contact are covered with a film of oil. If used constantly, the machine should be oiled daily, while with moderate use, an occasional oiling is sufficient. The small plate in front of the machine and the larger plate at the back should both be turned up and oil applied to the parts exposed. 5) is at its lowest, and a little oil rubbed over the surface of the shuttle race. There are also two holes in the hand attachment to which oil should be applied occasionally. When oiling, insert the oil can spout well into the holes. 16 27 & 28 To Oil the Machine continued. . . FIG. 15 After oiling, run the machine rapidly for a few minutes so that the oil may reach the bearings. Neglect to oil the machine will shorten its life and cause you trouble and annoyance. Always use SINGER oil. Inferior oil clogs the bearings, prevents efficient working, and causes rapid wear of the mechanism. 17 27 & 28 HINTS. The line F is the point at which to set the blued indicator for facings, the line B for binding, and the line C for cording or piping. Insert the material in the gauge with the edge against the blued indicator, and hold as shown above. [. . . ] Insert the edge of the material between the slide and the number gauge, and draw it backward and forward until the hem is formed, stopping with its end under the needle. Lower the presser bar and sew, taking care in guiding the work to keep the hemmer full. Felling can also be done by following the felling instructions. 29 27 & 28 The Adjustable Hemmer - Wide Hemming To make a hem more than one inch wide, loosen the screw, draw the slide to the right, as far as it will go, and turn it towards you, as in the illustration. Fold and crease down a hem of the desired width, pass the fold under the extension at the right of the hemmer, then insert the edge of the material into the folder, and proceed to sew. 30 27 & 28 The Under Braider - Braiding Fit the quilter foot, as shown. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SINGER NO. 27




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SINGER NO. 27 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.