User manual SINGER 675D DATASHEET

[. . . ] If the hot water system has not been used for such a period, turn on all hot water faucets and let the water flow from each for several minutes before using the washing machine. Do not smoke or use an open flame during this time, as the gas is flammable . Close supervision is necessary when the appliance is used near children. Before the appliance is removed from service or discarded, remove the door. [. . . ] The washer can no longer accept program changes and will continue to the end of the program. To cancel the program lock ^ Hold the "START" button until the "Door Lock" indicator goes out. Exception: The program selector was moved and the "Anti-crease/End" indicator blinks in the program sequence display. ^ Press the "START" button until the "Door Lock" indicator goes out. 20 Locking the washer Child Safety Lock This safety lock can be activated to prevent a child from climbing inside the washer. When the child safety lock is activated, the drum door cannot be opened and a program cannot be started. To activate the safety lock Before activating the lock: ­ the drum door must be closed, ­ the program selector must be at "End". Press the "Heavy Soil" button and hold the button pressed in during steps 3. Turn the program selector slowly in a clockwise motion to "COTTONS/ 140 °F". Turn the program selector slowly in a counterclockwise motion to "End". Turn the program selector slowly in a counterclockwise motion to the "DELICATES/cold" position. The "Door Lock" indicator (lower right of control panel) flashes. Fabric softener can be dispensed in the final rinse of these programs to reduce static cling. Spandex, microfibers etc. Drain / Spin DELICATES 105 °F / warm 85 °F / cold ß / cold SILK ß / cold WOOLENS 105 °F / warm 85 °F / cold ß / cold Jeans 105 °F Dress shirts 105 °F Starch Fine rinse No available wash options Available wash options: Soak, Heavy soil, Extended 7 6 6 B A ­ light colors dark colors lace or sheer fabrics, embroidered items. For synthetics, machine washable silks, satin, hosiery, lingerie, lace or crocheted (non-wool) items; curtains and knits. No available wash options 6 A silk and silk blends, lingerie and hosiery Ideal for machine and hand washable silks and other non-wool handwashable garments No available wash options 7 6 ­ 7 7 B A ­ B B light colors dark colors delicate woolens For hand washable and machine washable wool and wool blends (e. g. lamb's wool, cashmere, mohair, angora etc. ) No available wash options denim Available wash options: Soak, Heavy soil, Extended No available wash options No available wash options Washer care Cleaning the water inlet filters The washer has two water inlet filters to protect each inlet valve. These filters should be checked every 6 months and cleaned, if necessary. (This may need to be performed more frequently with some water supplies). , Inspect the hose regularly. The hose must be in good condition to withstand high water pressure. The hose should be replaced if there are cracks in the surface, or if it has been otherwise damaged or cut. Cleaning the inlet hose filter ^ Turn off the water valve. ^ Unscrew the inlet hose from the valve by turning the connector counterclockwise using a wrench, if necessary. Cleaning the filter in the inlet valve ^ Using a wrench, carefully loosen and remove the plastic hose connector on the inlet valve. ^ Remove the rubber seal, 1, from the connector. ^ Using needle nose pliers, grasp the plastic filter, 2, and pull it out of the hose connector. ^ Clean the filter under running water and carefully remove any large particles. ^ Slowly turn on the valve and check for leaks. ^ Using needle nose pliers, remove the plastic filter by pulling on the bar (see illustration). [. . . ] Both hoses must be connected to a water source, or the machine will not function properly. If the water pressure is greater that 145 psi (10 bar), a pressure reducer must be installed. If the water pressure is below 15 psi (1 bar), there will not be enough water available for a complete fill. Tips for a hot water connection ­ The hot water temperature from the hot water valve must not exceed 140°F; the ideal temperature is 130°F. [. . . ]