User manual SINGER 6212

[. . . ] Chapter-Page 1 1. 01 1. 02 1. 03 1. 04 1. 05 1. 05. 01 1. 05. 02 1. 06 2 3 3. 01 3. 02 3. 03 3. 04 4 5 5. 01 5. 02 5. 03 5. 04 6 7 7. 01 7. 02 7. 03 7. 04 7. 05 7. 06 7. 07 7. 08 7. 09 8 8. 01 8. 01. 01 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 General notes on safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Safety symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 76 dB(A) Noise measurement according to DIN 45 635-48-A-1 x v Subject to technical alterations Or comparable sizes of other thread types 3-1 Specifications 3. 02 Possible versions and subclasses Version B (only on 6212): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . For sewing medium materials Version CN: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . For sewing medium-heavy materials Work aids: Subclass -900/56 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic presser foot lift with backtacking system 3. 03 Maximum speeds of the SINGER 1295 Top feed stroke Version Max. speed (s. p. m. ) Up to 5. 5 mm B C 2200 1900 1800 1800 over 5. 5 mm to 7 mm B C 3. 04 Maximum speeds of the SINGER 6212 Top feed stroke Needle gauge Version Max. speed (s. p. m. ) up 5. 5 mm up 10 mm B C 2100 1800 1900 1600 1800 1600 1500 1400 from 10. 4 mm B C over 5. 5 mm up 10 mm B C from 10. 4 mm B C 3-2 Disposal of machine waste 4 Disposal of the machine q Proper disposal of the machine is the responsibility of the user. q The materials used for the machine are steel, aluminium, brass and various plastics. q The machine must be disposed of according to the locally valid pollution control regulations; if necessary, a specialist will have to be contracted. Care must be taken that parts soiled with lubricants are disposed of separately according to the locally valid pollution control regulations! 4-1 Transportation, packing and storage 5 5. 01 Transportation, packing and storage Transportation to the customer's premises Within the Federal Republic of Germany, complete machines (with table and motor) are delivered without packing. Machines without table (sewing heads only) and machines intended for exports are packed. 5. 02 Tansportation inside the customer's premises The manufacturer cannot be made liable for transportation inside the customer's premises nor to other operating locations. Care must be taken that the machines are only transported in an upright condition. 5. 03 Disposal of packing materials The packing materials of this machine comprise paper, cardboard and VCE fibre. Proper disposal of the packing material is the responsibility of the customer. 5. 04 Storage If the machine is not in use, it can be stored as it is for a period of up to six months, but after that it should be protected against dust and moisture. 8 - 01 q Loosen screws 1 and 2 and set the table at the required height. q Set the required pedal position and tighten tighten screw 2. 8-1 Installation and commissioning 8. 01. 02 Tensioning the v-belt q Loosen nuts 1. If a different motor is used, please refer to the instruction manual of the motor manufacturer. 2 cm 1 2 Fig. 8 - 02 8. 01. 03 Fitting the upper belt guard 6 If a large balance wheel is in use, break off corner 1 of belt guard part 3. Secure belt guard part 7 to the table top using woodscrews 8. 4 2 5 6 8 4 3 7 8 8 Fig. 8 - 03 8-2 Installation and commissioning 8. 01. 04 Fitting the lower belt guard q Position belt guard 1 so that motor pulley and v-belt can run freely. Fig. If a different motor is used, please refer to the instruction manual of the motor manufacturer. 1 Fig. 8 - 04 8. 01. 05 Fitting the synchroniser q Push synchroniser 1 onto the shaft. q Adjust the synchroniser (see Chapter 11. 05. 14, Adjusting the synchroniser). 2 1 Fig. 8 - 05 8-3 Installation and commissioning 8. 01. 06 Assembling the reel stand q Assemble the reel stand as shown in Fig. q Afterwards insert the stand in the hole in the table top and secure it with the nuts provided. Fig. [. . . ] After thread trimming, control lever 6 must pass freely on the right side of stop plate 3 and engage control lever 5 behind stop plate 3. There must be a clearance of 0. 2 mm between the pin of control cam 6 and the righthand inside of the control cam track. 0. 2 mm 4 5 2 3 1 7 6 Fig. 11 - 21 q Re-position stop plate 1 (screws 2) and stop plate 3 (screws 4) according to Requirement. 11 - 23 Adjustment 11. 05. 05 Thread-trimmer drive linkage Requirement 1. On the SINGER 6212 thread-catcher drive linkage 1 must have a length of 128 mm, less half of the needle gauge. [. . . ]