User manual SINGER 145W202

[. . . ] When the knob is on any of the settings other than "Off", the "H" operating light comes on. 9 How to Keep Your Cooktop in Shape Before cleaning or performing maintenance on your appliance, disconnect it from the electrical power supply. electric Hot Plates (only on certain models) The hot plates vary in diameter and power: "normal" and "fast". Avoid using abrasive products and abrasive sponges that could scratch the glass. [. . . ] Check to make sure that: • The gas holes on the burner are not clogged; • All of the movable parts that make up the burner are mounted correctly; • There are no draughts around the cooking surface. Check to make sure that: • You press the knob all the way in; • You keep the knob pressed in long enough to activate the safety device. € The gas holes are not clogged in the area corresponding to the safety device. • The minimum has been adjusted correctly (see the section entitled , "Minimum Regulation"). Check to make sure that: • The bottom of the cookware is perfectly flat. • The cookware is centered correctly on the burner or electric hot plate. If, despite all of these checks, the cooktop does not function properly and problem persists, call the nearest Merloni Elettrodomestici Customer Service Centre, informing them of: - The type of problem. Never call upon technicians not authorized by the manufacturer, and refuse to accept spare parts that are not original. Safety Is a Good Habit to Get Into To maintain the EFFICIENCY and SAFETY of this appliance, we recommend: • call only the Service Centers authorized by the manufacturer • always use original Spare Parts • • This manual is for a class 3 built-in cooktop. This appliance is designed for non-professional use in the home and its features and technical characteristics must not be modified. These instructions are only valid for the countries the symbols for which appear on the manual and the serial plate. It is also a good idea to keep only the tank currently being used in the room, making sure that it is not near sources of heat (ovens, fireplaces, stoves, etc. ) that could raise the internal temperature of the tank above 50°C. Installation of Built-in Cooktops The gas cooktops are equipped with type X degree protection against overheating. Therefore, the appliance can be installed next to cabinets, provided the height of the cabinet does not exceed that of the hob. For proper installation of the cooktop, the following guidlines must be followed: a) If the cabinet(s) located next to the cooktop are higher than the cooktop itself, the cabinet(s) must be installed at least 600 mm from the edge cooktop; b) Hoods must be installed in accordance with the instructions contained in the installation manual for the hoods themselves, and no less than 650 mm from the cooktop; c) The cabinets installed next to the hood must be located at a height of at least 420 mm from the top, (as shown in Fig. (exclusively for cooking appliances) Directly to the Outside b) The room must also allow for the influx of the air needed for proper combustion. The flow of air for combustion purposes must not be less than 2 m³/h per kW of installed capacity. The supply of said air can be effected by means of direct influx from the outside through a duct with a inner cross section of at least 100 cm² which must not be able to be accidentally blocked. Those appliances which are not fitted with a safety device to prevent the flame from accidentally going out must have a ventilation opening twice the size otherwise required, i. Otherwise, the room can be vented indirectly through adjacent rooms fitted with ventilation ducts to the outside as described above, as long as the adjacent rooms are not shared areas, bedrooms or present the risk of fire (Fig. C d) Should the cooktop be installed directly under a cupboard, the latter should be at least 700 mm (millimetres) from the top, as shown in Fig. [. . . ] €E” or Connect the Brown wire to the terminal marked “L” or coloured Red. Connect the Blue wire to the terminal marked “N” or coloured Black. Adapting the Cooktop for Different Types of Gas To adapt the cooktop to a different type of gas than that for which it was designed, (see the sticker under the hob or on the packaging), the burner nozzles must be changed, as follows: • Remove the pan supports and slide the burners out of the cooktop. € Unscrew the nozzles using a 7mm socket wrench and replace them with those for the new type of gas. [. . . ]