User manual SIMPLICITY 870S

[. . . ] They are for reference only. Copyright 2000 Slautterback Corporation Table of Contents 1 Safety Precautions for Hot Melt Applicator Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. 1 Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. 2 Personal Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. 3 Electrical Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Refer to Adhesive Flow Adjustment Section 5. 3. 3. 10 Super Squirt SS10G Mark II 19600-133 Rev. C 11/07/00 Copyright 2000 Slautterback Corporation [8] Tank Temperature Controller (not shown) A full-range adjustable thermostat sets and controls tank temperature. Located on the front of the melt tank base, it is accessible at the small access panel inside the electrical enclosure. Refer to Tank Temperature Controller, Section 5. 3. 1. [9] Hose Temperature Controller (not shown) An adjustable thermostat controller sets and controls hose temperature. Located on the thermal panel inside the electrical enclosure, the controller is attached to a capillary bulb sensor located in the hose. Refer to Hose Temperature Controller, Section 5. 3. 2. ® POWER 1 6 APPLICATOR ON OFF 2 ON PUMP OFF TANK TEMPERATURE HEATING OVERTEMP 5 4 3 2000345 © Copyright 2000 Slautterback Corporation Super Squirt SS10G Mark II 19600-133 Rev. C 11/07/00 11 5. 2 Startup Instructions ! DANGER: To avoid personal injury, follow all safety labels. Failure to properly operate and maintain equipment can lead to serious injury. Hot melt materials can cause severe burns resulting in disfigurement or blindness. Fire, explosion, personal injury, property and equipment damage can result if improper or unsafe materials are used. · Disconnect electrical power from external source to melt unit before undertaking maintenance or troubleshooting. To decrease pressure and adhesive flow, turn knob [1] counterclockwise. To achieve minimum pressure and lowest flow rate suitable for application, turn knob fully counterclockwise. Gradually turn clockwise until desired pressure and flow rate is reached. ® 1 2000359 14 Super Squirt SS10G Mark II 19600-133 Rev. C 11/07/00 Copyright 2000 Slautterback Corporation 6 Maintenance ! WARNING: Hot Melt materials can cause severe burns resulting in disfigurement or blindness. Follow these precautions before beginning any maintenance: · Wear protective clothing, safety goggles, and safety gloves. · Unless stated otherwise, always allow melt unit to cool before beginning any maintenance. · Disconnect hose electrical connector when hose fittings are disconnected and power is off. CAUTION: To prevent damage to components (hose fittings, etc. ), heat part(s) being serviced to approximately 121 °C (250°F) prior to dismantling, assembling, or adjusting. Heat parts by applying power to the unit using a hand held hot air gun or placing parts on a hot plate. Failure to do this will result in stripped threads and ruining both parts and tools. CAUTION: To avoid arcing of electrical contacts and possible failure of components, do not connect electrical connectors when the hose power switch is on. ! ! © Copyright 2000 Slautterback Corporation Super Squirt SS10G Mark II 19600-133 Rev. [. . . ] flow control valve Collar, Threaded, Locking, 5/16-24 Knob, 1-7/8", Black Plastic, 1/4-20 Fitting, 90°, 1/4 NPT to No. 8 JIC Nut, hex, 1/4-20 UNC O-ring, flow control valve piston (2) High Temp Lube, Clear, 5. 3 oz Tape, Teflon Sealant; 1/2" X . 0035" Part Number 73169-01 70123-8 70038-2 14490-5 70037-4 18508-1 11603-4A 70038-3 14445-01 14517-13 11409-84A 14441-GA 10412 11208 15015-2 6 1 2 3 4 12, 13 5 10 7 8 11 9 2000352 28 Super Squirt SS10G Mark II 19600-133 Rev. C 11/07/00 Copyright 2000 Slautterback Corporation 9. 3 V1 Pump Assembly Item 1 2 3 4 5 6 Gasket, V1 pump Pump, V1-675 O-ring, pump Shim, pump Kit, seal pump, V1 (includes hardware) Kit, hardware pump, V1 Description (Quantity) Part Number 70118 79048-3 10438 70032 79081 79042 1 2 3 4 5 6 2000366 © Copyright 2000 Slautterback Corporation Super Squirt SS10G Mark II 19600-133 Rev. C 11/07/00 29 9. 4 Motor Assembly Item * 1 2 3 4 5 6 7 8 9 Description (Quantity) Motor group, 38 rpm, 115 VAC, 60/50 Hz Coupling, 15. 88 mm (0. 625 in. ) shaft x 5. 08 cm (2 in. ) Key, 4. 76 mm (0. 1875 in. ) square x 5. 08 cm (2 in. ) Lg. [. . . ]