User manual SILVERCREST SL 65

[. . . ] Overview of Equipment Front side of the receiver Overview of Equipment Front side of the receiver 1 2 3 4 5 6 7 8 9 10 LED display ­ LED POWER OK MENU VOL + VOL ­ CH + CH ­ POWER Shows channel location or ttime Infrared sensor for the signal of the remote control LED is illuminated if the receiver is switched on or in standby mode Confirm Invokes main menu Increases volume Cursor moves to the right Decreases volume Cursor moves to the left Switches to the next higher channel location Cursor moves up Switches to the next lower channel location Cursor moves down Switches on and switches to the standby mode Rear side of the receiver Rear side of the receiver Remote control 1 2 3 4 5 6 7 8 9 10 11 12 13 RF OUT LNB IN VCR TV 100 ­ 240 V~ 50/60 Hz, 30 W 0/1 S-VHS COAXIAL OPTICAL RS 232 VIDEO AUDIO L AUDIO R LNB connection for a second satellite receiver LNB connection for the antenna cable SCART connection for the video set SCART connection for the TV set Mains connection Mains switch S-Video connection Digital coaxial audio output Digital optical audio output Serial port Analog video connection Left analog audio connection Right analog audio connection Remote control 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 POWER ZOOM LIST TIMER TEXT MUTE M/P V+ OK CH q FAV RECALL PAUSE INFO 0­9 P­ P+ V­ CH p MENU EXIT AUDIO EPG TV/SAT TV/RADIO Switches on and switches to the standby mode Enhances the TV image Shows favourits list (groups) Timer Teletext Turns off sound Without function Increases volume/cursor moves to the right Confirms menu or menu item Switches to the next lower channel location / cursor moves down Invokes favourits list Switches to previously selected channel Stills the frame Displays reception data of the current channel Selects channel directly, numerical input Scrolls pages down in menus Scrolls pages up in menus Decreases volume/cursor moves to the left Switches to the next higher channel location / cursor moves up Invokes main menu Exits menu or menu item Changes audio mode Electronic Program Guide (if offered) Switches between terrestrial and satellite antenna Switches between TV and radio mode -3- COMAG_BDA_SL65_S3_GB. indd Abs3:3 12. 05. 2005 17:47:17 Uhr Digital Satellite Receiver SL 65 Operating Manual Version 1, as of 03. 05. 2005 Preface This operating manual will help you in the · appropriate, · safe and · favorable usage of the digital satellite receiver, in short, the "receiver". We assume that the user of the receiver has overall knowledge regarding the handling of audio and video equipment. Each person who · installs, · connects, · operates, · cleans or · disposes of this receiver must be familiar with the entire content of this operating manual. Always keep this operating manual in the proximity of the receiver. Style Features Specific style features have been given in different sections of the operating manual. [. . . ] Insert the SCART cable in the SCART socket "VCR" on the receiver if you want to connect a video set. Follow the operating manual of the video set. 18 Connection diagram 19 Connection with the Cinch cable If you own a TV set not provided with a SCART socket, you can connect the receiver via a Cinch cable. Connect the "VIDEO" socket on the receiver to the video input of the TV set. Connect the "AUDIO-R" and "AUDIO-L" sockets of the receiver to the audio inputs of the TV set. 20 Connection diagram 21 Connection of an Audio-Digital Receiver If you want to use 5-channel audio transmission (Dolby digital sound/AC3), you must connect your audio-digital receiver to the optical or coaxial output of the receiver. Caution! Never connect the Phono input of your stereo system to the receiver; it may damage your stereo system. Strictly follow instructions for connecting the Cinch cable given in the operating manual of your stereo system. Caution! Please follow strictly the information regarding the connection in the operating manual of your audio-digital receiver. The optical and coaxial cables are not included in the scope of supply. You must switch on the TV set if you want to receive TV sound through your stereo system. 22 Connection of the coaxial digital output Insert the coaxial cable in the "COAXIAL" socket on the receiver. Connection diagram 23 Connection of the optical digital output Pull the protective cap out of the "OPTICAL" socket on the receiver. Insert the optical cable in the "OPTICAL" socket on the receiver. Connection diagram 24 Operation Remote control Two Micro type batteries are required for the remote control: LR 03/AAA/1. 5 V Open the battery compartment. Insert two batteries according to polarities mentioned on the battery compartment. Push the cover of the battery compartment carefully till the cover is locked. Always replace both batteries simultaneously and use batteries of the same type. If one battery has leaked, wear protective gloves and clean the battery compartment with a dry cloth. Caution! Batteries may contain toxic agents that are hazardous to health and environment. Therefore, dispose of the batteries immediately according to the prevailing statutory regulations. Please refer the overview of the remote control for functioning of the keys. Point the remote control towards the front side of the receiver and slightly press the corresponding key once. 25 Receiver Caution! Check that connections of all equipment and the antenna are proper before connecting the receiver to the mains. The numerical display of the receiver is not illuminated (display dark). Insert the mains plugs of the connected equipment in the mains socket and switch them on. Switch on the receiver via the red key on the top right on the remote control. The receiver is supplied with preprogrammed TV channels and can be used directly. If you want to check if new channels are available, initiate a scan for broadcasting stations. For this purpose, read the information on page 26. 26 Operation User interface on the TV monitor You can do individual settings of your receiver using the menus in the user interface. [. . . ] Do not use any cleaning agent containing solvents like petrol or thinners for cleaning. Clean the casing of the receiver with a dry cloth. 46 Troubleshooting Symptom The numerical display of the receiver is not illuminated and there is no sound or image Frontal display dark Possible cause and remedy The power cable is not connected. The receiver switches on and the program is displayed on the TV monitor. Check the cable connection from LNB to the receiver and from the receiver to the connected equipment. [. . . ]