User manual SILVERCREST KH 2156 UNIVERSAL REMOTE CONTROL

[. . . ] Universal remote Control 3a KH 2156 Universal remote Control operating manual KOMPERNASS GMBH BURGSTRASSE 21 D-44867 BOCHUM www. kompernass. com ID-Nr. : KH2156-08/09-V3 08/2009 KH 2156 INDEX Important safety instructions Device summary Initial use Unpacking the device / checking the package contents Inserting the batteries Operating components LCD display Buttons SETUP - System settings Code Setup (Programming the remote control) Programming by brand code search Programming by manual code input Programming by automatic code search System-Setup Setting the time Setting the date Adjust contrast Background Illumination System reset Timer Setup Sleep timer Event timer Learn Setup Code learn function Macro Setup Favourites channel Volume control Vol +/--, (Mute switching) For operation All OFF Faults / Remedies Disposal CE- Conformity Importer Technical data Important Warranty Notices PAGE 2 3 4 4 4 5 5 6 8 10 10 11 11 13 13 13 14 14 14 15 15 15 16 16 17 19 20 20 21 21 21 22 23 23 23 23 -1- Universal remote control KH2156 Read the operating instructions carefully before using the device for the first time and preserve this booklet for later reference. Pass this manual on to whoever might acquire the device at a future date. Important safety instructions Proper use Children may only operate the remote control under adult supervision. The universal remote control can replace a maximum of ten remote controls. It can only be used for entertainment electronics with infrared receivers. [. . . ] The notice "BACKLIT SETUP" appears again. System reset Via this function you can reset the URC to its factory default settings. 2. With the or button t select "SYSTEM SETUP" and confirm with the OK button k. 3. With the or button t select "SYSTEM RESET" and confirm with the OK button k. 4. In the LCD display q now appears "CONFIRM RESET" confirm the reset with the OK button k. All settings are now deleted and the menu will end. - 14 - Timer Setup The URC offers 2 timer modes, sleep timer and event timer. Sleep timer 1. Press the device button e for the device that is to be controlled (i. e. Press the OK button k "TIMER SLEEP" appears in the LCD display q. Confirm the selection of this function with the OK button k. 4. Now, below to the right in the LCD display q blinks the minutes for the remaining time of the selected device. Position the remote control in such a way that your infrared signal can reach the device to be switched off. After expiration of the set time the remote control will switch the device off. Then below to the left in the LCD display q "SL" will be shown. Event timer The remote control has 4 event timers available via which you are allowed to send out specific series of button combinations at designated times. 2. With the or button t select "TIMER SETUP" and confirm with the OK button k. "TIMER SLEEP" appears in the LCD display q. With the or button t select the desired memory slot "TIMER SETUP 1" to "TIMER SETUP 4" and confirm with the OK button k. Now the hour of the time of day, to which the desired button combinations are to be carried out, blinks. Set with the or button t the desired hour and press for confirmation the OK button k. Now the minutes of the time of day, to which the desired button combinations are to be carried out, blinks. Set with the or button t the desired minutes and press for confirmation the OK button k. 5. In the LCD display q you will see "TIMER X KEY" (X stands for the desired timer). Now press the desired device button e followed by the desired sequence of the button commands. 6. Press the S button r to save your entry and to return to the timer menu. Procede in a similar manner in order to, if required, programme the other timer memory slots also. - 15 - Tips: 1. Per timer memory slot a maximum of 14 buttons can be programmed. After entry of the 14th button the sequence will be automatically saved and "FULL" is shown in the LCD display q. In this menu also the device will return to the standard display after approx. [. . . ] Start the brand code search, the automatic code search or the direct code input (manual). > Press the corresponding device button e to set the URC to the correct mode. > In the event that the original RC does not have a "-/- -" button, change the programme with the CH+/-- buttons u or the number buttons o. > If this also does not work the child protection for the target device could be activated. [. . . ]