User manual SIEMENS A31008-M1037-B181-1-7619

[. . . ] 45 46 47 50 51 52 54 55 58 62 64 65 67 68 69 70 72 73 76 77 79 81 83 84 85 88 91 Administration . Checking the network settings and completing the installation procedure . For reasons of electrical safety, the router may only be opened by authorised service staff. Make sure you include these operating instructions when you pass on your router to someone else. 5 The Gigaset SE555 WLAN dsl The Gigaset SE555 WLAN dsl The Siemens Gigaset SE555 WLAN dsl is a powerful but simple communications device for connecting your PC or local area network (LAN) to the Internet (via DSL). [. . . ] The radio channel used for data transfer is shown in the Channel field. The Signal strength shows the strength of the connection to the repeater in percentage terms if such a connection exists. ì Click Refresh to update the display. ì Apply the settings by clicking OK. A detailed description of how to configure a network with repeaters can be found in the User Guide for the Gigaset WLAN Repeater 108, for example. 83 Configuring Advanced Settings USB Using your device's USB port, you and other users in the local network can u share a USB memory (see page 85) or u publish data on the Internet (see page 88) or u use a USB printer (see page 91). Note: The Gigaset SE555 WLAN dsl supports USB V 2. 0. Devices that support USB V 1. 1 may also be connected. ì In the USB menu, select Advanced Settings. ì Activate the USB port on the device. If a USB device is connected, its Status is displayed. Safely Remove Hardware ì Click this button and wait until any connected USB memory or USB printer is fully deactivated before disconnecting it from the device. ì Click OK to save the changes. Note: If a user is currently accessing the USB memory or the USB printer, a message window opens. Follow the instructions in this window. 84 Configuring Advanced Settings File Server The device's integrated file server allows you to manage folders and files in a connected USB memory (for example, a USB stick or a USB hard disk) and make them available to all users in the local network. ì Connect a USB data carrier to the Gigaset SE555 WLAN dsl via the USB port. The Gigaset SE555 WLAN dsl only supports hard disks with the FAT32 file system. Note: The USB interface of the Gigaset SE555 WLAN dsl supplies 480 mA of power. In this case the device must have its own mains adapter. ì In the USB menu, select File Server. ì Select the On option for the File Server. Enter a name for the file server in the Host name field. This is shown in the network environment of each computer in the local network and allows users to search for their file servers. If you assign a name other than SE555 (for example, the IP address for the Gigaset SE555 WLAN dsl), then the file server will appear in the Windows directory network environment both under the name "SE555" and under the name you have assigned. ì You can enter a Description of the file server in the next field. Note: When the USB memory is inserted, the first FAT32 partition is automatically enabled without security settings. 85 Configuring Advanced Settings ì Enter the name of the Domain / workgroup (WORKGROUP is the standard name for Windows) in which the file server is located. If you now search the network you will find the file server in the stated domain/workgroup in the network environment. Note: If you change the name of the workgroup, then it must also be changed in all the computers in your network. Otherwise you cannot access the file server. The connected USB memory is shown in the Device field. Partitions list and sharing directories All the partitions for the connected data carrier are shown under Partitions. ì Click the Edit button next to the partition whose directory you want to release for sharing. A new window now appears with a list of the existing shares. ì Click Add to set up a new share for the partition. ì For an existing share, click Edit to edit it. In both cases a window opens for the next steps (see page 87). ì To delete the required share, click the Delete button. ì Click Delete All Shares if you wish to cancel all existing shares. 86 Configuring Advanced Settings Setting up or editing a share ì Enter a name for the Share. You can enter the complete path for the directory manually or click on the Browse button. You can now set up access protection for the directory. ì First, select the On option for Security. ì Select the required option from the list next to Access: ì Select Depending on password if you wish to control access by means of a password. ­ Select Read only if you wish to release the data for reading (read only). ­ Select Full control if you wish to release the data for reading and writing. Depending on the chosen access option, you can now enter one password in the relevant field for read-only access or for full access, or else enter different passwords for read-only access and for full access. ì Now enter the password/passwords and confirm by entering it/them again. [. . . ] It will then direct incoming calls for a service via Port forwarding directly to the appropriate Port of the network component in question. WAN Wide Area Network A WAN is a network that is not restricted to one particular area, such as the Internet. A WAN is run by one or more public providers to enable private access. WEP Wired Equivalent Privacy WEP is a security protocol defined in the IEEE 802. 11 standard. [. . . ]