User manual SHERWOOD VR-670

[. . . ] Introduction READ THIS BEFORE OPERATING YOUR UNIT This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Note to CATV System Installer : This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. FCC INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] If you are familiar with a personal computer, you may easily understand the hierarchical file/folder construction. 19 ENGLISH Before starting playback For your convenience, the OSD(On-Screen-Display) language of this unit may be set to English as initial setting. If you want to change the OSD language to French, Italian, German, etc. , please refer to "When selecting the OSD Language" on page 35. ENGLISH BASIC PLAYBACK Preparations · Turn on the TV and select the video input source connected to the unit. · Set the TV screen type and the COMPONENT VIDEO OUTPUT SIGNAL correctly to match your TV. (Refer to "When selecting the TV Display" on page 34 and "CHANGING THE COMPONENT VIDEO OUTPUT SIGNAL" on page 32. ) Select DVD as input source. 1 Open the disc tray to load a disc with the printed side up, then close it. 2 · 8 cm (3 inch) discs can be loaded on the inside circle of the tray, too. · When a CD or DVD that doesn't contain any menu is loaded, playback automatically starts. Note : · Opening or closing the disc tray by force may damage it's mechanism. Note : · When you play a DVD Video that contains a menu or a MP3 disc, the menu display may appear on the TV screen. In this case, see "To start playback from the menu of DVD Video" below or "To start playback from the menu of MP3 disc" on the next page. · Example of DVD Video · Example of MP3 disc To start playback from the menu of DVD Video · Press the CURSOR button). /// buttons to select the preferred item and press the ENTER button (or PLAY/PAUSE( ) · Playback of the selected item starts. · When the selected item contains the subitems, repeat the above step until the preferred item is selected, To stop playback and return to the menu display · Press the TOP MENU or MENU button on the remote control. (Which button is pressed differs depending on the discs. ) · Playback is suspended and the menu display appears. 20 To start playback from the menu of MP3 disc In the stop mode, select the desired list mode. File list mode : It displays all the files on a disc, ignoring the folders in which they belong. · Example of folder list mode · Example of file list mode Press the CURSOR / buttons to select the preferred folder or file, then press the ENTER button. · When selecting the preferred file, playback starts from the selected file. · In the folder list mode, when selecting the preferred folder, the file menu screen of the selected folder is displayed. In this case, repeat this step to select the preferred file in its file menu. ) or BACKWARD · Each time the FORWARD SKIP( ) button is pressed, the next or previous SKIP( folder/file menu is skipped to. 2 Notes : · Depending on the MP3 disc and the condition of recording, some of MP3 discs may not be played or may be played differently. · The DVD Videos continues to rotate while the menu display appears. When no further selections are to be played, be sure to press the STOP( ) button repeatedly to enter the stop mode and to clear the menu display. · A TV screen may be burned out if a static picture is displayed for a long time in the stop or the pause mode, etc. . To prevent this, set the Screen Saver to ON (refer to "When selecting the Screen Saver" on page 35). Then, the unit automatically activates the screen saver function if a static picture, etc. Pressing any button will cancel the screen saver function and return to the previous display. · When you press a button, if the corresponding operation is prohibited by the unit or the disc, appears on your TV screen. To stop playback · When playback of DVD Video is stopped, the unit memorizes the point where the STOP( ) button was pressed(RESUME function: DVD Video only). ("R-STOP" is displayed on the unit's display when this function is activated. ) ) button again, and playback Press the PLAY/PAUSE( will resume from that point. [. . . ] · In case of DVD Video, turn the power off while playing back the desired scene. 49 ENGLISH 8 Continued When canceling the TIMER ENGLISH Press the SLEEP/TIMER button for more than 2 seconds to enter the timer setting mode. 1 · "TMR ON"(or "TMR OFF") is displayed. · To cancel the timer setting mode, press this button for more than 2 seconds again. Select the timer off mode. 2 · Each time the ENTER button is pressed, the timer mode changes as follows : "TMR ON" : Timer on mode(" "TMR OFF" : Timer off mode(" " lights up. ) " goes off. ) To confirm your selection, press the SLEEP/ TIMER button for more than 2 seconds. 3 · Then the timer is deactivated. ADJUSTING THE BRIGHTNESS OF THE DISPLAY · Each time the DIMMER button is pressed, the brightness of the display changes as follows : On dim off · In the display off mode, pressing any button will restore the display on mode. 50 Troubleshooting Guide ENGLISH If a fault occurs, run through the table below before taking your system for repair. If the fault persists, attempt to solve it by switching the unit off and on again. Under no circumstances should you attempt to repair the unit yourself. [. . . ]