User manual SHERWOOD TX5505

[. . . ] [Information on Disposal in other Countries outside the European Union] These symbols are only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal. Note for the battery symbol (bottom two symbol examples): The sign Pb below the symbol for batteries indicates that this batteries contains lead. EUROPE AUSTRALIA 220 V 240 V CAUTION • Leave a space around the unit for sufficient ventilation. • Avoid installation in extremely hot or cold locations, or in an area that is exposed to direct sunlight or heating equipment. [. . . ] AUTO TUNING button Press this button to search for a station of sufficient strength automatically. 7. Fluorescent display This displays operation status, frequency, RDS information, etc. 17. NUMERIC(0~9) buttons Press these buttons to specify the preset number of the station directly to be recalled or stored in the memory. 8. DIMMER button Each time this button is pressed, the brightness of the fluorescent display changes as follows : → ON → dimmer → OFF 18. MEMORY button Press this button to store the desired stations manually in the memory. 19. TUNING/PRESET MODE button Press this button to select the tunning mode(“P” goes off) or the preset mode (“P” lights up). When listening to FM broadcasts, press this button to enter the RDS menu. 10. TUNING/PRESET knob Rotate this knob to tune in the stations depending on whether the tuning mode or the preset mode is selected. 20. CURSOR ▲/▼/◀/▶and ENTER buttons Press the CURSOR ▲/▼/◀/▶ buttons to select items, etc. TUNING UP/DOWN (+/-) buttons Press these buttons to tune in the stations without selecting the tuning mode. 21. DISPLAY button Press this button to display RDS information. 7 ENGLISH 13. BAND button TX-5505(G)_ENG_100819_TX-5505(G)_ENG 2010-08-19 오후 5:31 페이지 8 REMOTE CONTROL OPERATION RANGE ENGLISH TUNING / PRESET STANDBY STEREO TUNED RDS ON/ STANDBY DIMMER T/ P MODE BAND AUTO PRESET AM / FM STEREO TUNER TX-5505 • Use the remote control unit within a range of about 7 meters (23 feet) and angles of up to 30 degrees aiming at the remote sensor. LOADING BATTERIES 1. Load two batteries(“AAA” size, 1. 5V) matching the polarity. • Remove the batteries when they are not used for a long time. • Do not use the rechargeable batteries (Ni-Cd type). 8 TX-5505(G)_ENG_100819_TX-5505(G)_ENG 2010-08-19 오후 5:31 페이지 9 Operations LISTENING TO RADIO BROADCASTS • Each time the BAND button on the remote control, the band changes as follows : FM ↔ AM • For details on FM mode, see “Listening to FM stereo broadcasts” on page 12. Before operation • Turn the power on. ON/ STANDBY or ■On the front panel 2. Press the TUNING/PRESET MODE button to select the tuning mode, then rotate the TUNING /PRESET knob over several steps once. • Each time the POWER ON/STANDBY button on the front panel is pressed, the tuner is turned on to enter the operating mode or off to enter the standby mode. • When it is in the standby mode, the STANDBY indicator lights up. This means that the tuner is not disconnected from the AC mains and a small amount of current is retained to support the operation readiness. • On the remote control, press the POWER ON button to enter the operating mode or press the STANDBY button to enter the standby mode. TUNING / PRESET T/ P MODE • Each time the TUNING/PRESET MODE button is pressed, the mode changes as follows : Tuning mode ↔ Preset mode (“P” goes off) (“P” lights up) Auto tuning 1. Press the AUTO TUNING button. or Band FM mode • “AUTO” is displayed and the tuner will now search until a station of sufficient strength has been found. The display shows the tuned frequency and the TUNED indicator lights up. • During auto tuning, press the TUNING UP(+)/DOWN(-) buttons to change the received frequency to a higher frequency or a lower frequency. • If the station found is not the desired one, simply repeat this operation. [. . . ] This could void the warranty. PROBLEM No power POSSIBLE CAUSE • The AC input cord is disconnected • Poor connection at AC wall outlet or the outlet is inactive. • Tune in the frequency of the desired station. Not receiving the stations Not receiving the preset stations Interference • Memorize the correct station frequency. • Install the outdoor antenna apart from the load. • Change the position of the antenna. Poor FM reception Continuous hissing noise during FM reception, especially when a stereo broadcast is received. Continuous or intermittent hissing noise during AM reception, especially at night. [. . . ]