User manual SHERWOOD SD-860

[. . . ] SD-860 Introduction READ THIS BEFORE OPERATING YOUR UNIT This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. FCC INFORMATION(FOR U. S. A. ) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Press the CURSOR / buttons to select the desired search mode. RC · The selected mode is highlighted. 2 Select the section to be played with pressing the NUMERIC buttons on the remote control. When entering title, chapter, group, track number Examples) For "3" : For "11" : When clearing the numbers entered before playback · Press the CLEAR button. RC When entering the elapsed time You can play a disc from the desired point by specifying the elapsed time from the beginning of the current title/group/file. 35 sec. " : · Then the numbers are all cleared. 3 Start playback from the selected section. Main unit RC RC or or Notes : · If the title/group/chapter/track/time you entered is not contained on the disc, search playback will not work. · Depending on the disc, a search playback will not work or may work differently. 21 PLAYING A SPECIFIC ITEM When using a title menu · If some DVDs which contain more than one title may have the menu like as a list of the titles, the TOP MENU button can be used to select the desired title. (The details of operation differ depending on the disc used. ) 1 During playback, press the TOP MENU button. RC Example) TITLE MENU Dogs Cows Cats Horses · Then a list of titles on the disc is displayed on TV screen. · If the disc does not have the menu such as a list of titles, this function does not work. 2 Press the CURSOR /// buttons to select the desired title, then press the ENTER or PLAY( ) button. RC RC Main unit RC or or · The unit starts playback of the selected title. · When the menu continues onto another screen, repeat this step until the desired title is selected. When using a DVD menu · Some DVDs have unique menu structures called DVD menus. For example, the discs programmed with complex contents provide guide menus, and those recorded with various languages provide menus for audio and subtitle language. Although the DVD menu's contents and operation differ from disc to disc, the following explains basic operation when this feature is used. 1 During playback, press the MENU button. RC Example) 1. AUDIO 2. ANGLE · Then the DVD menu available on the disc is displayed on TV screen. · If the disc does not have the DVD menu, this function does not work. 2 Press the CURSOR /// buttons to select the desired item, then press the ENTER or PLAY( ) button. RC RC Main unit RC or or · The unit starts playback of the selected item. · When the menu continues onto another screen, repeat this step until the desired item is selected. 22 REPEAT PLAYBACK · You can play a current title, group, chapter, folder, track, file, disc or part repeatedly. Note : · Repeat playback may not work correctly with some discs. Repeating a chapter/track, title/group During playback of the desired chapter/track or title/group, press the REPEAT( RC ) button. · Then the selected repeat mode is displayed on the TV screen. · Each time this button is pressed, the repeat mode changes depending on the disc types as follows : CHAPTER REPEAT ON : Chapter/track repeat : Title/group repeat : Repeat mode off (normal playback) REPEAT ONE : Track repeat : Entire disc repeat : Repeat mode off (normal playback) TITLE REPEAT ON REPEAT ALL REPEAT OFF REPEAT OFF · To return to normal playback, press the REPEAT( ) button repeatedly until the "REPEAT OFF" is displayed. Repeating a file, folder 1 In the stop mode, press the REPEAT( RC ) button. · Each time this button is pressed, one of the various playback modes is selected and displayed on the TV screen as follows: REPEAT ONE : File repeat : Folder repeat : Normal playback of the disc : Entire disc repeat : Normal playback of a file : Normal playback of a folder FOLDER REPEAT DISC DISC REPEAT SINGLE FOLDER 2 To select the desired file, perform the steps 1 and 2 in "To start playback from the menu of MP3, WMA, JPEG or DivX disc" on page 16. · Playback starts from the selected file according to the selected playback mode. 23 Continued Repeating the desired part 1 During playback at the beginning of the part you want to repeat, press the REPEAT A/B button. RC · Then "A TO B SET A" is displayed on the TV screen. 2 At the end of the part, press the REPEAT A/B button again. · Then "A TO B REPEAT ON" or "A TO B SET B" is displayed on the TV screen, and the part between points A and B is played back repeatedly. · To return to normal playback, press the REPEAT A/B button repeatedly until "A TO B CANCELLED" is displayed. Notes : · You may not use the repeat A/B playback of the part that includes multiple camera angles. · Repeat A/B playback works only within a title or a track. PLAYING TRACKS/FILES IN RANDOM ORDER · During playback, press the RANDOM PLAY button. RC · Then the selected playback mode is displayed for several seconds on the TV screen. · Each time this button is pressed, the playback mode changes depending on the disc types as follows: RANDOM ON : Random playback Track on the disc are played back in random order. RANDOM OFF : Normal playback. · To return to normal playback, press the RANDOM PLAY button during random playback or in the stop mode, then "RANDOM OFF" is displayed. Note : · Random playback may not work correctly with some discs. 24 PLAYING TRACKS IN DESIRED ORDER · Up to 25 tracks can be programmed to be played in any desired order. In the stop mode, press the PROGRAM button. RC PROGRAM P 00:00 1 · Then the program mode is displayed on the TV screen. · When the PROGRAM button is pressed again, the program mode is canceled. 2 Select the desired track with pressing the NUMERIC buttons on the remote control. · For 5 : · For 12 : PROGRAM P 01:05 PROGRAM P 02:12 Programmed track number Programmed order 3 4 Repeat the above step 2 until the desired tracks are programmed. To start program playback, press the PLAY( ) button or the ENTER button. Main unit RC RC or or · Playback will start in the programmed order. · After all programmed tracks have been played, it enters the stop mode without clearing the programmed tracks. (Program playback is suspended. ) Clearing the programmed tracks [ To clear one by one ] · During programming, press the CLEAR button. RC · Each time this button is pressed, the programmed tracks are cleared one by one in the opposite order. · Once program playback is performed, you cannot clear one by one. [ To clear all programmed tracks ] · During programming or when the STOP( ) button is pressed to stop program playback, press the PROGRAM button. RC · Then the programmed tracks are all cleared. [. . . ] Though the number of audio channels is 5. 1 which is same as Dolby Digital, discs bearing the provides fat sound and better signal-to-noise ratio, thanks to the lower audio compression ratio format. It also provides wide dynamic range and better separation, resulting in magnificent sound. "DTS" and "DTS Digital Surround" are registered trademarks of Digital Theater Systems, Inc. Bitstream The digital signal form of multichannel audio data (e. g. , 5. 1 channel) before it is decoded into its various channels. Linear PCM PCM stands for Pulse Code Modulation. Linear PCM is the usual digital method without compression, used for audio playback of audio CDs, DVD Videos, etc. 50 Troubleshooting Guide If a fault occurs, run through the table below before taking your receiver for repair. [. . . ]