User manual SHERWOOD RX-773

[. . . ] Introduction READ THIS BEFORE OPERATING YOUR UNIT ENGLISH This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Caution regarding installation Note : For heat dispersal, do not install this unit in a confined space such as a bookcase or similar enclosure. Do not block ventilation openings or stack other equipment on the top. FOR YOUR SAFETY Units shipped to Australia are designed for operation on 230 V AC only. To ensure safe operation, the three-pin plug supplied must be inserted only into a standard threepin power point which is effectively earthed through the normal household wiring. [. . . ] · Before operating audio and video components other than this receiver with using this remote control, the setup code for each component should be entered. · For system remote control operation, "000" was stored previously in the memory of the device button "CD" for Sherwood CD player, "DVD" for Sherwood DVD player, "AUX" for Sherwood tape deck and "TV" for Sherwood TV respectively as its factory setup code. So, you don't need to enter its code for each Sherwood component except in such a case that its code does not work. Entering a setup code 1. Find the setup codes according to the type and the brand name of your component, referring to "Setup Code Table" on page 28. 4. Enter a 3 digit code, aiming the remote control at the remote sensor on the component. Press and hold down both the "ENTER/MEMORY" button and the desired one of the DEVICE buttons for more than 1 seconds. · If entering is performed successfully, the LED will flicker twice. · To be sure that the setup code is correct, press the POWER ON(or STANDBY) button. · When your component is not turned off, repeat the above steps 2 to 4, trying each code for your component until you find one that works. Notes: · If the LED did not flicker twice, then repeat the above steps 3 to 4 and try entering the same code again. · Manufacturers may use different setup codes for the same product category. For that reason, it is important that you check to see if the code you have entered operates as many controls as possible. If only a few functions operate, check to see if another code will work with more buttons. · The LED will flicker once. Note : The "AUD" button is unavailable for the audio components other than this receiver. 5. Repeat the above steps 1 to 4 for each of your components. 13 ENGLISH Using a punch-through function This remote control may be programmed to operate either the AUDIO volume punch-through or the TV volume and/or TV channel punch-through in conjunction with any of the eight components controlled by this remote control. For example, since this receiver will likely be used as the sound system while watching TV, you may want to adjust this receiver's volume although this remote control is set to control the TV. · When programming this remote control for the AUDIO volume punch-through, press and hold down both "AUD" button and "VOLUME " button for more than 1 second. ENGLISH · If programming is performed successfully, the LED will flicker twice. · When you want either TV volume or TV channel punchthrough, press and hold down both "TV" button and either "VOLUME " or "CHANNEL " button for more than 1 second. Note: If you use one of AUDIO and TV volume punchthrough functions, you cannot use the other. Removing a punch-through function · When removing the AUDIO volume punch-through, press and hold down both "AUD" button and "VOLUME more than 1 second. " button for · If removing is performed successfully, the LED will flicker twice. · When you want to remove either TV volume or TV channel punch-through, press and hold down both "TV" button and either "VOLUME " or "CHANNEL " button for more than 1 second. 14 Programming a macro function · The macro function enables you to program a series of button operations(up to 10) on this remote control into a single button. · You can store up to three separate macro command sequences into "M1", "M2" and "M3" buttons. and one of three NUMERIC buttons ("1"~"3") corresponding to "M1"~"M3" buttons for more than 1 second. [. . . ] · Even when this receiver enters the standby mode, in such a case that "R2" is dimly lit, meaning only the ROOM2 circuitry operates, the ROOM2 source can be played independently. Therefore, when you do not use the ROOM2 function, turn off the ROOM2 function to save electricity. · To enjoy ROOM2 source, turn on the ROOM2 function and adjust the ROOM2 settings as below. ENGLISH 1. Select the desired ROOM2 speakers. or or · "R2 > ~ " is displayed for several seconds. [. . . ]