User manual SHERWOOD RX-4208

[. . . ] This symbol indicates the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. This symbol indicates important operating and maintenance (servicing) instructions in the literature accompanying the appliance. wARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK , DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION •• Leave space around the unit for sufficient ventilation. [. . . ] TONE DIRECT PRESET •• With the receiver in Standby mode, you can also turn the power on by pressing an Input Selector button on the remote control. 1 4 7 PRESET TU N E PRES ET 2 5 8 0 3 6 9 MO/ST A SPEAKER L R B E BLUETOOTH A LAN C DISPLAY S EL SEARCH MODE MEMO/ ENTER B DIMMER SLEEP •• When using the headphone, press the corresponding speaker button to switch off both A and B speakers. 16 T UN E SEL Operating Your System Muting the Sound You can mute the sound temporarily by pressing MUTE. Adjusting the Tone (Bass and Treble) You can adjust the tone (bass and treble) as desired. TONE DIRECT PRESET MUTE VOLUME PRES ET TU N E S EL MEMO/ ENTER T UN E MUTE VOLUME TU N E L R B E BLUETOOTH A LAN C DISPLAY SEARCH MODE 2 Press MUTE or VOLUME - / + to turn on the sound. TONE DIRECT PRESET PRES ET L R B E BLUETOOTH A LAN C DISPLAY S EL SEARCH MODE SEARCH MODE MEMO/ ENTER MUTE VOLUME PRES ET L R B E BLUETOOTH A LAN C DISPLAY S EL MEMO/ ENTER •• If you want to listen to a program source without the tone effect, select the tone direct mode by pressing TONE DIRECT. SEARCH MODE T UN E 2 Adjusting the Sound Balance (Left and Right) Adjust the tone as desired by pressing BASS -/+ or Treble -/+. €¢â€¢ The tone level can be adjusted within the range of -10 ~ +10 dB. •• It is recommended the bass and treble to be adjusted to 0 dB (flat level). TONE DIRECT PRESET TU N E PRES ET TU N E S EL MEMO/ ENTER T UN E L R B E BLUETOOTH A LAN C DISPLAY SEARCH MODE PRES ET •• When you set a preset number by pressing numeric buttons on the remote control, you can skip the step 4. l R B E BLUETOOTH A LAN C DISPLAY S EL SEARCH MODE MEMO/ ENTER 4 Confirm your selection. •• On the remote control , press MEMO/ ENTER. €¢â€¢ The station has now been stored in the memory. €¢â€¢ A stored station is erased from the memory by storing another station in its place. TONE DIRECT PRESET •• Auto preset is performed only when you select FM tuner as a input source. €¢â€¢ FM stations with weak signal strength cannot be stored to memory. MUTE VOLUME PRES ET L R B E BLUETOOTH A LAN C DISPLAY S EL MEMO/ ENTER T UN E SEARCH MODE 5 Repeat the above steps 1 - 4 to store another station. t UN E SEL TU N E MUTE VOLUME SEL SEL 19 RX-4508 AM/FM STEREO RECEIVER Tuning in to Preset Stations 1 Select a desired preset number. €¢â€¢ On the main unit, press ◄ or ►. €¢â€¢ The receiver starts scanning the stations in the preset sequence. 4 5 8 0 6 9 MO/ST SLEEP MUTE VOLUME B DIMMER TU N E S EL MEMO/ ENTER T UN E L R B E BLUETOOTH A LAN C DISPLAY •• If you select a desired preset number by pressing ◄ or ► on the main unit, be sure to select preset mode. When you select preset mode, "PRESET" is displayed on the display panel. [. . . ] €¢â€¢ When the sleep time is selected, the fluorescent display is dimly lit. 4 5 8 0 6 9 MO/ST SLEEP B DIMMER CD AUX PHONO TUNER 7 PRESET Setting the Auto Power Control You can set the standby time for the system to be turned off. CD AUX PHONO TUNER 1 Press and hold SLEEP for more than 3 seconds. €¢â€¢ Each time this button is pressed, the auto power control time changes as follows: Off  2h  4h  6h 4 7 PRESET 5 8 0 6 9 MO/ST B DIMMER SLEEP CD AUX PHONO TUNER 23 Troubleshooting If you experience any of the following difficulties while using the system, use this troubleshooting guide to help remedy the problem before requesting servicing. [. . . ]