User manual SHERWOOD RV-4060

[. . . ] OPERATINGINSTRUCTIONS AUDIO/VIDEO RECEIVER RV-4060R REMOTE SENSOR VOLUME/TONE/BALANCE POWER STANDBY/OFF STANDBY VOL FM AM AUTO MEMO MHz STEREO KHz MONO MUTE TAPE M TEST VIDEO12 SLEEP CH NR WI PH PRO LOGIC BASS TREBLE 3-STEREO BALANCE PHONES MEMORY MODE TUNING/PRESET RESET TAPE MONITOR SURROUND VCR 2/CAMCORDER INPUT FM AM VCR 1 VCR 2 TV/AUX CD VIDEO L -AUDIO- R RV-4060R AUDIO/VIDEO RECEIVER INTRODUCTION UNPACKING AND INSTALLATION READ THIS BEFORE OPERATING YOUR UNIT FOR U. S. A. AND CANADA 120 V ENGLISH Congratulations on Your Purchase! Your new high fidelity Receiver is designed to deliver maximum enjoyment and years of trouble free service. It will explain the features and operation of your unit and help ensure a trouble free installation. They will be helpful if you ever need to move your unit and may be required if you ever need to return it for service. [. . . ] CENTER MODE ­ for selecting the desired center mode when in Dolby Pro Logic or Dolby 3 Stereo mode. TEST TONE ­ for checking the output level of the front, center and rear speakers. CENTER LEVEL / ­ for adjusting the center level (only in normal mode or wide mode). REAR LEVEL / ­ for adjusting the rear level (in Dolby Pro Logic mode) 32. FM MODE­ for selecting the stereo or mono mode when listening to FM. TAPE MON ­ for monitoring the sound of recording or playback of cassette deck. FILE ­ for selecting desired equalizer pattern in the preset or user mode. 19. ­ for recording. In the DIGI LINK III remote control system, if pressing PLAY, etc. on CD or Deck, CD or TAPE MONITOR is selected automatically without selecting the input and PLAY, etc. (as described in amplifier chapter titled "POWER STANDBY/ON). COMPACT DISC PLAYER AMPLIFIER POWER ON/OFF ENGLISH Press the POWER switch to turn the power on. ­ The receiver enters the operating mode and the respective indicators lights up. POWER STANDBY/ON In the operating mode, press the POWER button on the remote control. ­ The receiver enters the standby mode, the respective indicators light off and the standby indicator lights up. In the standby mode, the receiver is not disconnected from the AC mains and a small amount of current is retained to support the memorized contents and operation readiness. ­ If the electricity fails or the AC cord is leaved unplugged for more than 2 weeks(power off mode), the memorized contents are all cleared. ­ The power is turned on, the respective indicators light up and the standby indictor lights off. SOUND CONTROL Volume Adjust the overall volume with MASTER VOLUME. Adjust the stereo balance between the left and the right channel with the VOLUME/TONE/BALANCE control. Adjust the high tones from MIN to MAX with the VOLUME/TONE/BALANCE control. Adjust the bass tones from MIN to MAX with the VOLUME/TONE/BALANCE control. Use SURROUND MODE to select the desired sound effect: PRO LOGIC, 3 STEREO Press MUTE on the remote control if you want to silence the speakers temporarily. INPUT SELECTION Select the desired input on the receiver or the remote control. ­ When the TAPE MONITOR button is set to on so that "TAPE M" indicator lights up, other inputs can not be heard from the speakers. [. . . ] DUBBING FROM VCR2 TO VCR1 Select VCR2 as program source to be recorded. ­ The audio and video signals from VCR2 will be dubbed onto the tape in VCR1. When dubbing from VCR2 to VCR1, you can replace the audio signal from VCR2 with the signal from an audio source, e. g. ­ You can now watch the picture from VCR2 on your TV and listen to the sound from the audio source while recording. MAINTENANCE Do not leave the unit in direct sunlight or other places where high temperatures can occur for any length of time, such as in the vicinity of a heating source. [. . . ]