User manual SHERWOOD RNC-200

[. . . ] Home Theater Master Preprogrammed & Learning Remote Control SL-9000 Operating Manual Table of Contents Page Introduction Battery Installation A. Preprogrammed Set Up Three Digit Code Method Auto Search Method Recalling the Set Up Code Number C. Learning Set Up Learning New Functions on the Main Keypad Learning New Functions on Device Buttons Erasing Learned Functions Erasing Individual Buttons Erasing All Buttons in One Device Mode Erasing All Buttons in All Device Modes D. Operation Device Buttons Main Device Mode Automatic Audio Mode Backlighting Advanced Features A. [. . . ] Erasing All Buttons in All Device Modes 1 Press and hold the TV Device Button and the LIGHT button simultaneously, for approximately ten seconds. The LCD will flash ERASE ten times, flash CLEAR and then return to the TV mode. When the LCD on the remote returns to TV, all the learned functions in all eight Device modes have been erased. All the buttons in all Device modes will now operate with the preprogrammed functions in their respective modes. 18 Using Your Remote D: Operation After you have programmed the remote control for your equipment, use the following procedures to operate your home entertainment system: 1 Press the Device Button that you wish to operate: e. g. to operate a TV, press the TV Device Button; to operate a VCR, press the VCR Device Button, etc. 2 Aim the remote control at the device and press the POWER button to turn on the device. 3 Press the buttons that send out the commands you desire. Note: Some audio/video devices have separate buttons for POWER ON and POWER OFF. To operate these devices on the remote, press the corresponding DEVICE Button to turn the equipment ON and press the POWER button to turn the equipment OFF. Please try all the functions of this remote control with your equipment. However, some of the secondary functions might be stored under a button that has a different name from the one on your original remote control. Please refer to the Function Tables on pages (5 - 7) for details. 19 Using Your Remote Device Buttons Any press of a Device button at the top of the remote control can perform the following functions: 1 Changes the Device mode on the SL-9000 remote control. 2 Sends out a preprogrammed POWER ON command for a AUD AUD CD CD DVD DVD AUX AUX SAT SAT TV TV VCR VCR CBL CBL Device, if applicable. 3 Sends out a learned and/or joined selection. 4 Toggles between the Main Device mode and the Automatic VOL CH MUTE MUTE T/ V T/ V POWER Audio mode if the Automatic Audio Mode is active. GUIDE GUIDE MENU MENU PAUSE PAUSE Joining to Device Buttons R R E E W W SEL SEL PLAY PLAY F F . . F F The 10 preprogrammed Audio input selects and the keypad buttons 0-9 found on the SL-9000 in the AUDIO Device mode can be joined to individual Device buttons. Once joined, any press of 1 the Device button will also emit the 2 3 joined command. STOP STOP EXIT EXIT PRE. CH CH FAV FAV SLEEP SLEEP 4 AUD 5 CD 6 DVD INFO INFO PRO. L PRO. L AUX 7 SAT 8 TV 9 VCR ENTER ENTER SHIFT SHIFT NEXT NEXT 3. CH 3. CH CBL Device Buttons +10 PIP PIP 0 ALT ALT TEST TEST POWER TUNER TUNER MUTE TAPE1 CD TAPE1 CD T/ V VOL TAPE2 PHONO TAPE2 PHONO CH Audio Input Buttons VCR1 VCR2/SAT LDP AUX VCR1 VCR2/SAT LDP AUX GUIDE M1 M2 M3 M1 M2 M3 PAUSE TV TV MENU M4 M4 Setting Up: 1 Press the AUDIO and ENTER buttons simultaneously on R E W LIGHT LIGHT SEL PLAY F . JOIN will appear in the LCD. LEARNING REMOTE CONTROL LEARNING REMOTE CONTROL STOP HOME THEATER MASTER 2 Press the Device button that you would like to assign a EXIT PRE. CLEAR will flash and INPUT will then 1 2 3 appear in the LCD. FAV SLEEP 3 Select a button to be joined from the remote control, e. g. The LCD will display 2 IN_XX indicating +10 0Audio input selected (IN_V1, the IN_V2, IN_CD, etc. or IN_0, IN_1, IN_2 etc. ) and then JOIN. NEXT 3. CH ENTER SHIFT ALT PIP TEST TUNER CD TAPE1 20 TAPE2 PHONO VCR1 VCR2/SAT LDP AUX TV M1 M2 M3 M4 LIGHT HOME THEATER MASTER LEARNING REMOTE CONTROL Using Your Remote 4 Press the ENTER button. SAVE will flash twice and the LCD will return to AUDIO indicating that the joined function has been stored. Every time that the Device button is pressed it will also emit the joined function. To erase a joined function from a Device button: 1 Press the AUDIO and ENTER buttons simultaneously on the remote control. [. . . ] First, using the VCR Device button, program the remote via standard set-up to operate the first VCR. Then, program your second VCR into a Device Button that is not being used, e. g. , AUX using this method. 1 Turn on the device. 2 On the remote control, press the Device Button that you will assign for the device and the MUTE button, simultaneously. SET will appear in the LCD. 3 Press the Device Button that corresponds to the original device. [. . . ]