User manual SHERWOOD RD-6513

[. . . ] cover 2008. 8. 21 12:21 PM 2 OPERATING INSTRUCTIONS RD-6513 AUDIO/VIDEO RECEIVER RD-6513(A) 2008. 8. 21 12:19 PM 3 IMPORTANT SAFETY INSTRUCTIONS 1. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. [. . . ] Select the desired one of REF 1 and REF 2. · If the preset memory disappears, perform the above step 1 again. 3. Confirm your selection. · The adjusted channel levels have now been memorized into the selected memory. Recalling the memorized channel levels 1. Press the CHANNEL LEVEL button. · "CAL " (or "REF 1", etc. ) is displayed for several seconds. · If the channel level mode display disappears, press this button again. 2. Select the desired one of REF 1 and REF 2. · Then the channel levels memorized into the selected preset memory are recalled. 23 RD-6513(A) 2008. 8. 21 12:19 PM 24 LISTENING TO RADIO BROADCASTS Auto tuning ENGLISH 1. Select the desired band. Manual tuning · Manual tuning is useful when you already know the frequency of the desired station. · After selecting the desired band, press the TUNING UP(+) / DOWN(-) buttons repeatedly until the right frequency has been reached. · Each time this button is pressed, the band changes as follows ; FM ST FM MONO AM ("ST" lights up) ("ST" goes off) Auto presetting · When FM stereo broadcasts are poor because of weak broadcast signals, select the FM mono mode to reduce the noise, then FM broadcasts are reproduced in monaural sound. · Auto presetting function automatically searches for FM stations only and store them in the memory. · While listening to FM radio broadcasts, press and hold down the (MEMORY/) ENTER button for more than 2 seconds. 2. Press the TUNING UP(+)/DOWN(-) buttons for more than 0. 5 second. · The tuner will now search until a station of sufficient strength has been found. · If the station found is not the desired one, simply repeat this operation. · Weak stations are skipped during auto tuning. · Then "AUTO MEM" flickers and this receiver starts auto presetting. · To memorize AM stations or weak stations, preform "Manual presetting" procedure with using "Manual tuning" operation. 24 RD-6513(A) 2008. 8. 21 12:19 PM 25 Manual presetting · You can store up to 30 preferred stations in the memory. Tuning to preset stations · After selecting the tuner as an input source, select the desired preset number. 1. Press the (MEMORY/)ENTER button. ENGLISH · When using the NUMERIC buttons on the remote control. Examples) For "3" : MEM tuning. For "15" : For "30" : · "MEM" is flickering for several seconds. 3. Select the desired preset number (1~30) and press the (MEMORY/)ENTER button. · When using the NUMERIC buttons on the remote control. Examples) For "3" : For "15" : For "30" : · The station has now been stored in the memory. · When using the NUMERIC buttons, the station is stored automatically without pressing the (MEMORY/)ENTER button. · A stored frequency is erased from the memory by storing another frequency in its place. · If "MEM" goes off, start again from the above step 2. 4. Repeat the above steps1 to 3 to memorize other stations. MEMORY BACKUP FUNCTION The following items, set before the receiver is turned off, are memorized. · INPUT SELECTOR settings · Surround mode settings · Preset stations, etc. 25 RD-6513(A) 2008. 8. 21 12:19 PM 26 RECORDING · The analog signals from the EXTERNAL INs as well as the digital signals from the coaxial or optical digital input can be heard but cannot be recorded. [. . . ] 1 Vp-p S-Video (luminance signal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Vp-p (chrominance signal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 286 Vp-p Component video (R-Y signal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 5 Vp-p (B-Y signal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]